| About |
|---|
| CALIBRE™ 603-6 Polycarbonate Resin is a branched polycarbonate resin specially designed for multi-wall sheet extrusion. CALIBRE 603-6 offers a high melt strength to calibrate effectively a wide range of multi-wall sheet structures from low to high complexity, such as seven wall sheet. CALIBRE 603-6 offers a wider processing window than CALIBRE 503-5 and is likewise specially designed to give excellent sheet surface quality at high line speeds with a reduced tendency to display chatter marks. CALIBRE 603-6 contains a UV absorber additive, but sheets for outdoor applications require a protective UV-absorbing cap layer. It is recommended to coextrude a 50 micron thick cap layer from CALIBRE 320UV. Main Characteristics: Wide processing window High surface quality Minimizes chatter marks Applications: Low to high complexity multi-wall sheets&& |
| Product Description | |
|---|---|
| Supplier | Trinseo |
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Good melt strength,HB |
| Availabilitys | Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.20 | g/cm³ | ISO 1183/B |
| Melt Flow Rate | |||
| 300℃，1.20kg | 6.0 | g/10min | ISO 1133 |
| Shrinkage rate | |||
| MD | 0.50 to 0.70 | % | ISO 294-4 |
| Water absorption rate | |||
| Equilibrium, 23 ℃, 50% RH | 0.32 | % | ISO 62 |
| 23℃，24hr | 0.15 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2350 | MPa | ISO 527-2/50 |
| tensile strength | |||
| fracture | 66.0 | MPa | ISO 527-2/50 |
| yield | 62.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| yield | 6.0 | % | ISO 527-2/50 |
| Bending modulus | 2400 | MPa | ISO 178 |
| bending strength | 93.0 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -30℃ | 16 | kJ/m² | ISO 179/1eA |
| 23℃ | 55 | kJ/m² | ISO 179/1eA |
| Impact strength of cantilever beam notch | ISO 180/A | ||
| -30℃ | 15 | kJ/m² | ISO 180-A |
| 23℃ | 80 | kJ/m² | ISO 180-A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, annealed | 142 | ℃ | ISO 75-2/A |
| 1.8 MPa, unannealed | 126 | ℃ | ISO 75-2/A |
| 0.45 MPa, annealed | 145 | ℃ | ISO 75-2/B |
| Vicat Softening Temp | |||
| B50 | 150 | ℃ | ISO 306 |
| Linear coefficient of thermal expansion | |||
| MD | 7.0E-5 | 1/℃ | ISO 11359-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Compared to the leakage tracing index | |||
| 2.00 mm, solution A | 250 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 1.50 mm | HB | UL 94 | |
| 3.00 mm | HB | UL 94 | |
| Glowing wire flammability index | IEC 60695-2-12 | ||
| 1.0 mm | 900 | ℃ | IEC 60695-2-12 |
| 2.0 mm | 875 | ℃ | IEC 60695-2-12 |
| 3.0 mm | 875 | ℃ | IEC 60695-2-12 |
| Igniting temperature of the hot wire | IEC 60695-2-13 | ||
| 1 mm | 800 | ℃ | IEC 60695-2-13 |
| 2 mm | 775 | ℃ | IEC 60695-2-13 |
| 3 mm | 775 | ℃ | IEC 60695-2-13 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Refractive index | 1.586 | ISO 489 | |
| Transmittance | 86.0 to 90.0 | % | ASTM D1003 |
| Haze | 1.0 | % | ASTM D1003 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 3. This rating not intended to reflect hazards presented by this or any other material under actual fire conditions. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |