| About |
|---|
| Cawiton® MT960 is a Styrene Ethylene Butylene Styrene Block Copolymer (SEBS) material. It is available in Europe for injection molding. Important attributes of Cawiton® MT960 are: Sterilizable Copolymer Food Contact Acceptable Typical application of Cawiton® MT960: Medical/Healthcare&& |
| Product Description | |
|---|---|
| Generic | SEBS |
| Material Status | Commercial: Active |
| Features | Steam sterilized,Food contact compliance,Block Copolymer,Radiation disinfection,Ethylene oxide disinfection |
| Availabilitys | Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.900 | g/cm³ | ISO 2781 |
| Melt Flow Rate | |||
| 230℃，5.0kg | 5.6 | g/10min | ISO 1133 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s A | 60 | ISO 868 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ISO 37 | ||
| TD, 100% strain | 1.80 | MPa | ISO 37 |
| MD, 100% strain | 2.70 | MPa | ISO 37 |
| TD, 200% strain | 2.30 | MPa | ISO 37 |
| MD, 200% strain | 3.10 | MPa | ISO 37 |
| TD, 300% strain | 3.00 | MPa | ISO 37 |
| MD, 300% strain | 3.30 | MPa | ISO 37 |
| tensile strength | ISO 37 | ||
| TD, yield | 11.9 | MPa | ISO 37 |
| MD, yield | 3.70 | MPa | ISO 37 |
| Tensile strain | ISO 37 | ||
| TD, fracture | 630 | % | ISO 37 |
| Flow rate, fracture | 300 | % | ISO 37 |
| tear strength | ISO 34-1 | ||
| TD | 24 | kN/m | ISO 34-1 |
| MD | 30 | kN/m | ISO 34-1 |
| Compression deformation | |||
| 70℃，22 hr | 51 | % | ISO 815 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | |||
| DSC | 166 | ℃ | DSC |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Hopper temperature | 30 to 60 | °C | |
| Barrel rear temperature | 180 to 220 | °C | |
| Barrel middle temperature | 190 to 230 | °C | |
| Barrel front temperature | 190 to 230 | °C | |
| Nozzle temperature | 200 to 240 | °C | |
| Processing (melt) temperature | 180 to 240 | °C | |
| Mold temperature | 20 to 40 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Measured with a differential scanning calorimeter |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |