| About |
|---|
| Product Description | |
|---|---|
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Melt Flow Rate | |||
| 300℃，1.2kg | 15 | g/10min | ISO 1133 |
| Density | |||
| 23℃，50%RH | 1.2 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| TD | 0.5-0.7 | % | ISO 294-4 |
| MD | 0.5-0.7 | % | ISO 294-4 |
| Water absorption rate | |||
| 23℃，24hr | 0.32 | % | ISO 62 |
| 23℃，50%RH | 0.15 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 1mm/min | 2340 | MPa | ISO 527-2 |
| tensile strength | |||
| Yield, 50mm/min | 60 | MPa | ISO 527-2 |
| Tensile strain | |||
| Yield, 50mm/min | 6 | % | ISO 527-2 |
| Fracture, 50mm/min | 150 | % | ISO 527-2 |
| Bending modulus | |||
| 2mm/min | 2410 | MPa | ISO 178 |
| bending strength | |||
| Yield, 2mm/min | 97 | MPa | ISO 178 |
| Rockwell hardness | |||
| R-level | 120 | ISO 2039-2 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 75 | kJ/m² | ISO 179 |
| Charpy Unnotch Impact strength | |||
| 23℃ | N | kJ/m² | ISO 179 |
| Impact strength of cantilever beam notch | |||
| 23℃ | 70 | KJ/m² | ISO 180/1A |
| Notched impact strength of cantilever beam | |||
| 23℃ | N | KJ/m² | ISO 180/1U |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Glass transition temperature | |||
| 10℃/min | 148 | ℃ | ISO 11357-2 |
| Hot deformation temperature | |||
| 0.45MPa, annealed | 143 | ℃ | ISO 75-2/B |
| 1.8MPa, unannealed | 127 | ℃ | ISO 75-2/A |
| Vicat Softening Temp | |||
| 50N，50℃/h | 148 | ℃ | ISO 306/B50 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | |||
| D102.0x2.0mm | 1.00E+16 | ohm | IEC 60093 |
| Volume resistivity | |||
| D102.0x2.0mm | 2.00E+17 | ohm·cm | IEC 60093 |
| Dielectric strength | |||
| 1mm | 34 | kV/mm | IEC 60243 |
| Dissipation factor | |||
| 100Hz | 0.001 | IEC 60250 | |
| 1MHz | 0.01 | IEC 60250 | |
| Dielectric constant | |||
| 100Hz | 3.1 | IEC 60250 | |
| 1MHz | 3 | IEC 60250 | |
| Compared to the leakage tracing index | 250 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.5mm | HB | UL 94 | |
| 3mm | HB | UL 94 | |
| Extreme oxygen index | 27 | % | ISO 4589-2 |
| Glowing wire flammability index | |||
| 1.5mm | 875 | ℃ | IEC 60695-2-12 |
| 3mm | 930 | ℃ | IEC 60695-2-12 |
| Glowing wire ignition index | |||
| 1.5mm | 875 | ℃ | IEC 60695-2-13 |
| 3mm | 875 | ℃ | IEC 60695-2-13 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Refractive index | 1.586 | ISO 489 | |
| Transmittance | |||
| 2mm | 89 | % | ISO 13468 |
| Haze | |||
| 2mm | <0.8 | % | ISO 14782 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |