| About |
|---|
| Chemlon® 100 W is a Polyamide 66 (Nylon 66) material. It is available in Asia Pacific, Europe, or North America for injection molding. Primary attribute of Chemlon® 100 W: Flame Rated.&& |
| Product Description | |
|---|---|
| Supplier | Teknor Apex |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | V-2 |
| Availabilitys | Asia Pacific,North America,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.16 | g/cm³ | ISO 1183 |
| Molding shrinkage | 1.2-1.8 | % | ISO 294-4 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile Strength | 90.39 | MPa | ISO 527-2 |
| Tensile Strain | |||
| Broken BRK | 7.0 | % | ISO 527 |
| Flexural Modulus | 3105 | MPa | ISO 178 |
| Flexural Strength | 115.23 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Izod Notched Impact strength | 3.57 | KJ/m² | ISO 180/1A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature HDT | |||
| 1.82 MPa | 85 | ℃ | ISO 75-1/-2 |
| Melting temperature | 260 | ℃ | ISO 11357-3 |
| ELECTRICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume Resistance | 1E18 | ohms·cm | IEC 60093 |
| Electric strength | 430 | V/mil | IEC 60243-1 |
| Compared Tracking Index | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame Class Rating | |||
| 0.8 mm | V-2 | UL 94 | |
| Oxygen Index | 28 | % | ASTM D2863 |
| FMVSS flame retardant rating | PASSES | FMVSS 302 |
| Process Conditions | |||
|---|---|---|---|
| Injection Molding | Nominal value | Unit | Test method |
| Drying Temperature | 79 | °C | |
| Maximum Moisture Content | 0.20 | % | |
| Suggested maximum proportion of recycled materials | 25 | % | |
| Rear Temperature Zone 1 | 241 to 254 | °C | |
| Middle Temperature Zone 2 | 257 to 271 | °C | |
| Front Temperature Zone 3 | 263 to 282 | °C | |
| Nozzle temperature | 263 to 279 | °C | |
| Melt Temperature | 263 to 279 | °C | |
| Mold Temperature | 21 to 93 | °C | |
| Injection Pressure | 34.5 to 138 | MPa | |
| Screw Speed | 60 to 120 | rpm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |