| About |
|---|
| Cogegum® XLPO-HFFR-可交联无卤阻燃复合物 硅烷接枝化合物通过加入催化剂母料（ SIOPLAS ®方法）进行湿气固化。包括含有阻燃体系的聚烯烃基体，使电缆具有自行熄灭功能，不释放卤酸、有毒和腐蚀性气体以及黑烟。该材料符合RoHS指令的要求。 符合以下标准： – EN 50363-0 G10； EN50363-5 EI8； EN50363-6 EM10； IEC 60092/351 HF90； Cenelec HD 624.6；VDE 0266 HXI1， HXM1； VDE 0250 HI3； VDE 0207 HJ1， HM1。&& |
| Product Description | |
|---|---|
| Supplier | Solvay |
| Generic | 聚烯烃，共挤薄膜用聚烯烃 |
| Material Status | Commercial: Active |
| Features | Low smoke,Crosslinked,Halogen free,Flame Characteristics,Low toxicity,Self-extinguishing |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.34 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 190℃，21.6kg | 7.0 | g/10min | Internal Method |
| Water absorption rate | |||
| 100℃，24hr | < 4.00 | mg/cm² | IEC 60811 |
| ESCR(Environmental Stress Cracking Resistance) | |||
| Condition A, 50 ℃, 3.00 mm, 10% non-ionic surfactant, molded | > 1000 | hr | ASTM D1693 |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Changes in mechanical properties after air bomb aging test at 0.5MPa, 127 ℃, 40 hr | IEC 60811 | ||
| Change in tensile elongation | -10 | % | IEC 60811 |
| Changes in mechanical properties after hot air aging test, 150 ℃, 240 hr | IEC 60811 | ||
| The rate of change in tensile strength | 20 | % | IEC 60811 |
| Change in tensile elongation | -12 | % | IEC 60811 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| impact test | |||
| thermosetting | IEC 60811 | ||
| Maximum permanent elongation after cooling: 250 ℃ | 0.0 | % | IEC 60811 |
| Elongation at break under load: 250 ℃ | 60 | % | IEC 60811 |
| Hot air shrinkage | |||
| 1 hour, 100 ℃ | < 4.0 | % | IEC 60811 |
| Hot press test | |||
| Maximum permeability, K=0.6125 ℃ | < 50 | % | IEC 60811 |
| Bending test | |||
| -40℃ | 通过 | IEC 60811 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | IEC 60502 | ||
| 20 ℃ | 8.2E+14 | ohms·cm | IEC 60502 |
| 90 ℃ | 5.4E+14 | ohms·cm | IEC 60502 |
| Insulation resistance constant | IEC 60502 | ||
| 20℃ | 3000 | Mohms·km | IEC 60502 |
| 90℃ | 2000 | Mohms·km | IEC 60502 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Extreme oxygen index | 31 | % | ASTM D2863 |
| Discharge of halogenated acid | < 0.10 | % | IEC 60754-1 |
| Latent heat energy | |||
| High level, total value | 20.3 | MJ/kg | ISO 1716 |
| Temperature index | |||
| burning | 300 | ℃ | NES 715 |
| Corrosive gases in flue gas | IEC 60754-2 | ||
| PH value | > 4.30 | IEC 60754-2 | |
| Conductivity | < 10.0 | µS/mm | IEC 60754-2 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 36 | ISO 868 | |
| tensile strength | |||
| fracture | 13.0 | MPa | IEC 60811 |
| Tensile strain | |||
| fracture | 290 | % | IEC 60811 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Barrel 1 zone temperature | 130 to 150 | °C | |
| Barrel 2 zone temperature | 140 to 160 | °C | |
| Barrel 3 zone temperature | 140 to 160 | °C | |
| Barrel 4 zone temperature | 150 to 170 | °C | |
| Ring temperature | 160 to 180 | °C | |
| Head temperature | 160 to 180 | °C | |
| Nozzle temperature | 170 to 220 | °C | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |