| About |
|---|
| HAC-M is injection a molding aesthetic resin.HAC-M is a color creativity plan.HAC-M is mainly used in appearance items of household appliance,etc.&& |
| Product Description | |
|---|---|
| Supplier | KumhoSunny |
| Generic | PC+ABS |
| Material Status | Commercial: Active |
| Features | Good surface appearance,HB,V-0 |
| Availabilitys | Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.20 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 260℃，5.0kg | 50 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD | 0.40 to 0.60 | % | ASTM D955 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 3.2mm | 200 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 85.0 | ℃ | ASTM D648 |
| Vicat Softening Temp | 95.0 | ℃ | ASTM D1525 2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+15 | ohms | IEC 60093 |
| Volume resistivity | > 1.0E+15 | ohms·cm | IEC 60093 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.60 mm | V-0 | UL 94 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | > 90 | ASTM D523 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 110 | ASTM D785 | |
| Pencil hardness | |||
| 500g | HB | ||
| tensile strength | 60.0 | MPa | ASTM D638 |
| Bending modulus | 2300 | MPa | ASTM D790 |
| bending strength | 78.0 | MPa | ASTM D790 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 90 to 110 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Recommended maximum moisture content | 0.030 | % | |
| Barrel rear temperature | 210 to 240 | °C | |
| Barrel middle temperature | 220 to 245 | °C | |
| Barrel front temperature | 230 to 255 | °C | |
| Nozzle temperature | 230 to 250 | °C | |
| Processing (melt) temperature | 240 to 250 | °C | |
| Mold temperature | 85 to 95 | °C | |
| Back pressure | 0.300 to 1.00 | MPa | |
| Screw speed | 40 to 55 | rpm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Rate B (120°C/h) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |