| About |
|---|
| CONATHANE EN-1554 is a polyether based polyurethane resin system primarily intended for use as a molding, encapsulating and potting compound for harness breakouts, watertight electrical connectors, cables, cable end seals, printed circuitry and other electrical components. The system also has utility in the casting or molding of mechanical parts and as a lining material for pumps, chutes and conveyors, where outstanding abrasion resistance is a necessity. CONATHANE EN-1554 may be cured at room or elevated temperatures. CONATHANE EN-1554, when fully cured, is a tough, cold-flow resistant elastomer that has good resistance to oils, gasoline, JP-4 fuel, water, and seawater and also provides outstanding protection against corrosion or contamination. The system is funginert when tested in accordance with MIL-E-5262C and MIL-STD-810B. Three primers have been developed for use in bonding EN-1554 to metals, neoprene, and polyvinyl chloride during the curing process. CONAP® AD-1146 is recommended for metals, CONAP® PR-1167 for neoprene, and CONAP® AD-1161 for polyvinyl chloride.&& |
| Product Description | |
|---|---|
| Supplier | Cytec Industries |
| Generic | PUR |
| Material Status | Commercial: Active |
| Features | Good flexibility,Corrosion Resistant,Moisture resistance,Low temperature toughness,Good wear resistance,Grease resistance,Gasoline resistance |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | |||
| — | 1.09 | g/cm³ | |
| — | 0.998 to 1.20 | g/cm³ | |
| Water absorption rate | |||
| 4hr immersed in D I. @ 00 ° F in water | 0.33 | % | |
| Shrinkage rate | |||
| Volume | 4.5 | % | |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tear strength | 61.3 | kN/m | |
| Compression deformation | |||
| 70℃，22 hr | 50 | % |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength | |||
| 70 ℃, 336 hours in water | -11 | % |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | |||
| — | 2.5E+10 | ohms | |
| — | 2.5E+12 | ohms | |
| Volume resistivity | |||
| 25 ℃ | 5.1E+12 | ohms·cm | |
| 121 ℃ | 6.3E+10 | ohms·cm | |
| Dielectric strength | |||
| 1.27 mm | 24 | kV/mm | |
| 3.18 mm | 12 | kV/mm | |
| Dielectric constant | ASTM D150 | ||
| 25 ℃，1 kHz | 6.63 | ||
| 25 ℃，1 MHz | 5.23 | ||
| Arc resistance | 120 | sec | |
| insulation resistance | |||
| 25℃ | 5.8E+11 | ohms |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Thermosetting components | |||
| resin | 按重量计算的混合比: 100 | ||
| Hardening method | 按重量计算的混合比: 33 | ||
| Thermosetting mixed viscosity | |||
| 25℃ | 15000 | cP | |
| 25℃ | 20000 | cP |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Isocyanate Content | 4.9 to 5.3 | % | |
| Mixed System | 100 | % | |
| Antifungal activity | Non-nutrient |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s A | 84 to 90 | ||
| Tensile modulus | |||
| 300% secant | 7.58 | MPa | Internal Method |
| tensile strength | 31.0 | MPa | |
| Tensile strain | |||
| fracture | 550 | % |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Mix |
| 3. Hardener |
| 4. Die C |
| 5. 250°F |
| 6. 77°F |
| 7. Resin |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |