CONTINUUM™ DMDA-1260 NT 7

About
CONTINUUM™ DMDA-1260 NT 7 High Density Polyethylene Resin (HDPE) is intended for use in compression and injection molded beverage closures designed primarily for applications that undergo hot fill or aseptic sterilization processes. CONTINUUM™ DMDA-1260 offers improved performance for injection molded fitments designed for fitted pouches where its balance of properties are desired. CONTINUUM™ DMDA-1260 delivers a combination of improved properties such as improved stiffness, higher heat deflection temperature, improved ESCR, and easy processing versus alternative HDPE systems typically used for hot fill and aseptic sterilization processes. The end results are longer term closure performance, easy opening closures without the use of slip agent and consistent processing. Main Characteristics: – Excellent Stiffness, ESCR, and Impact Strength – Excellent Sensory Properties – Excellent Processing Characteristics – High Heat Deflection Temperature – Controlled Sensory Properties Complies with: U.S. FDA 21 CFR 177.1520(c)3.2a Europe Commission Regulation (EU) No 10/2011 Consult the regulations for complete details.&&

About

CONTINUUM™ DMDA-1260 NT 7 High Density Polyethylene Resin (HDPE) is intended for use in compression and injection molded beverage closures designed primarily for applications that undergo hot fill or aseptic sterilization processes. CONTINUUM™ DMDA-1260 offers improved performance for injection molded fitments designed for fitted pouches where its balance of properties are desired. CONTINUUM™ DMDA-1260 delivers a combination of improved properties such as improved stiffness, higher heat deflection temperature, improved ESCR, and easy processing versus alternative HDPE systems typically used for hot fill and aseptic sterilization processes. The end results are longer term closure performance, easy opening closures without the use of slip agent and consistent processing. Main Characteristics: – Excellent Stiffness, ESCR, and Impact Strength – Excellent Sensory Properties – Excellent Processing Characteristics – High Heat Deflection Temperature – Controlled Sensory Properties Complies with: U.S. FDA 21 CFR 177.1520(c)3.2a Europe Commission Regulation (EU) No 10/2011 Consult the regulations for complete details.&&

Product Description
Supplier	DOW
Generic	HDPE
Material Status	Commercial: Active
Availabilitys	North America,Latin America

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.963	g/cm³	ASTM D792
Melt Flow Rate
190℃，2.16kg	2.7	g/10min	ASTM D1238
ESCR(Environmental Stress Cracking Resistance)			ASTM D1693
50 ℃, 10% non-ionic surfactant, F50	22.0	hr	ASTM D1693
50 ℃, 100% non-ionic surfactant, F50	28.0	hr	ASTM D1693

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	79.4	℃	ASTM D648
Vicat Softening Temp	131	℃	ASTM D1525
Melting temperature
DSC	135	℃	Internal Method
Crystallization peak temperature
DSC	118	℃	Internal Method

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D	60		ASTM D2240
tensile strength			ASTM D638
yield	29.6	MPa	ASTM D638
fracture	20.7	MPa	ASTM D638
Tensile strain			ASTM D638
yield	7.0	%	ASTM D638
fracture	700	%	ASTM D638
Bending modulus
2% secant	1410	MPa	ASTM D790-B

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.