| About |
|---|
| 高冲击和延展性在 (23 °C) 和 (-29° C)之间 |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PC+ABS |
| Material Status | Commercial: Active |
| Features | High impact resistance,Low temperature ductility |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| tensile strength | |||
| Yield, 50 mm/min | 60 | MPa | ASTM D638 |
| Tensile strain | |||
| Yield, 50 mm/min | 5 | % | ASTM D638 |
| Fracture, 50 mm/min | 75 | % | ASTM D638 |
| Tensile modulus | |||
| 50 mm/min | 2240 | MPa | ASTM D638 |
| bending strength | |||
| Yield, 1.30 mm/min, 50 mm span | 88 | MPa | ASTM D790 |
| Bending modulus | |||
| 1.3 mm/min，50mm跨距 | 2420 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 650 | J/m | ASTM D256 |
| -30℃ | 270 | J/m | ASTM D256 |
| Total energy of instrument impact | |||
| 23℃ | 63 | J | ASTM D 3763 |
| -30℃ | 56 | J | ASTM D 3763 |
| Instrument impact energy peak, | |||
| 23℃ | 63 | J | ASTM D 3763 |
| -30℃ | 49 | J | ASTM D 3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | |||
| 3.2mm | 126 | ℃ | ASTM D 648 |
| 6.4mm | 110 | ℃ | ASTM D 648 |
| Linear coefficient of thermal expansion | |||
| MD：-40~40℃ | 7.2E-05 | 1/℃ | ASTM E 831 |
| Relative temperature index | |||
| Electrical performance | 60 | ℃ | UL 746B |
| Impact mechanical performance | 60 | ℃ | UL 746B |
| Non mechanical impact performance | 60 | ℃ | UL 746B |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.14 | ASTM D792 | |
| Shrinkage rate | |||
| MD：3.2 mm | 0.5- 0.7 | % | Internal Method |
| Melt Flow Rate | |||
| 260℃，3.80kg | 12 | g/10min | ASTM D1238 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot wire ignition {PLC | 3 | PLC Code | UL 746A |
| Arc resistance | |||
| Tungsten wire | 5 | PLC Code | ASTM D495 |
| High voltage arc marking rate {PLC | 1 | PLC Code | UL 746A |
| High current arc ignition (surface {PLC) | 0 | PLC Code | UL 746A |
| Compared to the leakage tracing index | 3 | PLC Code | UL 746A |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant rating, 94HB flame rating evaluation | 1.21 | mm | UL 94 |
| ultraviolet radiation | |||
| Water exposure/immersion | F2 | UL 746C |
| Process Conditions | |||
|---|---|---|---|
| injection molding | Nominal value | Unit | Test method |
| Drying temperature | 105 – 110 | °C | |
| Drying time | 3 – 4 | hrs | |
| Drying time (cumulative) | 8 | hrs | |
| Maximum water content | 0.04 | % | |
| Melt temperature | 275 – 300 | °C | |
| Nozzle temperature | 275 – 300 | °C | |
| Front Section Zone 3 Temperature | 260 – 300 | °C | |
| Temperature in Zone 2 of the middle section | 255 – 295 | °C | |
| Temperature in Zone 1 of the rear section | 250 – 290 | °C | |
| Mold temperature | 60 – 90 | °C | |
| Back pressure | 0.3 – 0.7 | MPa | |
| Screw speed | 40 – 70 | rpm | |
| Shoot to cylinder size | 30 – 80 | % | |
| Depth of exhaust groove | 0.038 – 0.076 | mm | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |