CYCOLOY™ CE3210 resin

About
阻燃的PC/ ABS共混物,使用非溴化和非氯化阻燃系统，具有高冲击性能和优良的挤出和热成型特性。

Product Description
Supplier	SABIC
Generic	PC+ABS
Material Status	Commercial: Active
Features	Weather resistance is good,High impact resistance,High Heat Resistance,Low temperature ductility
Availabilitys	Africa & Middle East ,Europe

Technical Data
MECHANICAL	Nominal value	Unit	Test method
tensile strength
Yield, Type I, 50 mm/min	63	MPa	ASTM D638
Fracture, Type I, 50 mm/min	51	MPa	ASTM D638
Tensile strain
Yield, Type I, 50 mm/min	4	%	ASTM D638
Fracture, Type I, 50 mm/min	55	%	ASTM D638
bending strength
Yield, 2 mm/min	95	MPa	ISO 178
Yield, 1.30 mm/min, 50 mm span	97	MPa	ASTM D790
Bending modulus
Yield, 2 mm/min	2700	MPa	ISO 178
1.3 mm/min，50mm跨距	2440	MPa	ASTM D790
tensile strength
50 mm/min
Tensile strain
yield	65	MPa	ISO 527
50 mm/min
Tensile modulus
fracture	55	MPa	ISO 527
50 mm/min	2780	MPa	ASTM D638
1 mm/min	2650	MPa	ISO 527
yield	4	%	ISO 527
fracture	75	%	ISO 527

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23℃	685	J/m	ASTM D256
23℃，80103	50	kJ/m²	ISO 180-1A
-30℃，80103	13	kJ/m²	ISO 180-1A
23℃，80104	45	kJ/m²	ISO 180-1A
80104 -30℃	15	kJ/m²	ISO 180-1A
Charpy Notched Impact Strength
23 ℃, 80 * 10 * 3, 62mm span	50	kJ/m²	ISO 179/1eA
-30 ℃, 80 * 10 * 3, 62mm span	13	kJ/m²	ISO 179/1eA
23 ℃, 80 * 10 * 4, 62mm span	48	kJ/m²	ISO 179/1eA

THERMAL	Nominal value	Unit	Test method
Vicat Softening Temp	105	℃	ASTM D1525
Hot deformation temperature
1.8 MPa, 64 mm span	90	℃	ISO 75/Af
Unannealed, 3.2 mm
Linear expansion coefficient, -40 ℃ to 40 ℃
flow	7.5E-0.5	1/℃	ISO 11359-2
transverse	7.5E-0.5	1/℃	ISO 11359-2
Ball pressure test
75℃±2℃	75		IEC 60695-10-2
0.45 MPa	97	℃	ASTM D 648
Vicat Softening Temp
1.8MPa	88	℃	ASTM D 648
B50	104	℃	ISO 306
B120	107	℃	ISO 306
Relative temperature index
Electrical performance	85	℃	UL 746B
Impact mechanical performance	70	℃	UL 746B
Non mechanical impact performance	85	℃	UL 746B

PHYSICAL	Nominal value	Unit	Test method
Density	1.22	g/cm³	ASTM D792
Shrinkage rate
MD	0.4 – 0.6	%	Internal Method
Melt Flow Rate
260℃，5.0kg	11.2	g/10min	ASTM D1238
Density	1.18	g/cm³	ISO 1183
Water absorption rate
Saturation, 23 ℃	0.6	%	ISO 62
23℃，50% RH	0.2	%	ISO 62
Melt Volume Rate
260℃，5 kg	11	cm³/10min	ISO 1133

Electrical performance	Nominal value	Unit	Test method
Volume resistivity	>1.E+15	ohms·cm	IEC 60093
Surface resistivity	>1.0E+15	ohms	IEC 60093
Dielectric strength
0.8 mm in oil	35	kV/mm	IEC 60243-1
1.6 mm in oil	25	kV/mm	IEC 60243-1
3.2 mm in oil	17	kV/mm	IEC 60243-1
Relative permittivity
1 MHz	2.7		IEC 60250
50-60 Hz	2.8		IEC 60250
Dissipation factor
50-60 Hz	0.004		IEC 60250
1 MHz	0.006		IEC 60250

FLAME CHARACTERISTICS	Nominal value	Test method
Flame retardant level
1.50 mm	V-0	UL 94
2.50 mm	5VB	UL 94

Process Conditions
injection molding	Nominal value	Unit	Test method
Drying temperature	80 – 85	°C
Drying time	2 – 4	hrs
Melt temperature	230 – 270	°C
Barrel 1 zone temperature	235 – 260	°C
Barrel 2 zone temperature	240 – 265	°C
Barrel 3 zone temperature	245 – 270	°C
Barrel 4 zone temperature	245 – 270	°C
Hopper temperature	60 – 80	°C
Adjuster temperature	245 – 270	°C
Core temperature	235 – 260	°C
Calibrator temperature	60 – 80	°C

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.