| About |
|---|
| PC/ABS, extrusion and blow molding grade.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PC+ABS |
| Material Status | Commercial: Active |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.13 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.40 to 0.70 | % | Internal Method |
| Water absorption rate | |||
| Equilibrium, 23 ℃ | 0.40 | % | ASTM D570 |
| 24hr | 0.10 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2070 | MPa | ASTM D638 |
| tensile strength | |||
| yield | 52.4 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 100 | % | ASTM D638 |
| yield | 5.0 | % | ASTM D638 |
| Bending modulus | |||
| 50 mm span | 2070 | MPa | ASTM D790 |
| bending strength | |||
| Yield, 50 mm span | 77.2 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ASTM D256 | ||
| -30℃ | 430 | J/m | ASTM D256 |
| 23℃ | 530 | J/m | ASTM D256 |
| Dart impact equipped with measuring instruments | ASTM D3763 | ||
| -30℃，Total Energy | 47.5 | J | ASTM D3763 |
| 23℃，Total Energy | 54.2 | J | ASTM D3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 3.2 mm | 104 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 3.2 mm | 124 | ℃ | ASTM D648 |
| Linear coefficient of thermal expansion | |||
| MD：-40~40℃ | 8.1E-5 | 1/℃ | ASTM E831 |
| Thermal conductivity coefficient | 0.20 | W/m/K | ASTM C177 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 99 to 110 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Recommended maximum moisture content | 0.040 to 0.050 | % | |
| Barrel 1 zone temperature | 238 to 249 | °C | |
| Barrel 2 zone temperature | 238 to 254 | °C | |
| Barrel 3 zone temperature | 238 to 254 | °C | |
| Barrel 4 zone temperature | 238 to 257 | °C | |
| Barrel 5 zone temperature | 243 to 260 | °C | |
| Connector temperature | 243 to 260 | °C | |
| Nozzle temperature | 249 to 266 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 2.0 in/min |
| 3. Type I, 2.0 in/min |
| 4. 0.051 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |