| About |
|---|
| Daplen EE189HP is a 15% mineral filled polypropylene compound intended for injection moulding. This material has an excellent balance between impact strength and stiffness, gives a good surface quality and is easy to process. Applications Daplen EE189HP has been developed especially for the car industry to be used in automotive interior parts. Door panels and pockets Center consoles Window frames Other automotive interior parts Special Features High scratch resistance No tendency to show stickiness after outdoor exposure&& |
| Product Description | |
|---|---|
| Supplier | Borealis AG |
| Generic | Polyolefin Elastomer |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good surface appearance,High impact resistance,Renewable resources,High scratch resistance |
| Availabilitys | Africa & Middle East ,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.00 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 13 | g/10min | ISO 1133 |
| Shrinkage rate | |||
| MD | 0.95 | % | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 1 mm | 1700 | MPa | ISO 527-2 |
| tensile strength | 21.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| yield | 5.0 | % | ISO 527-2 |
| Bending modulus | 1750 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -20℃ | 3.5 | kJ/m² | ISO 179/1eA |
| 23℃ | 26 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -20℃ | 95 | kJ/m² | ISO 179/1eU |
| 23℃ | No Break | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 52.0 | ℃ | ISO 75-2/Ae |
| 0.45 MPa, unannealed | 94.0 | ℃ | ISO 75-2/Be |
| Vicat Softening Temp | |||
| — | 128 | ℃ | ISO 306/A |
| — | 51.0 | ℃ | ISO 306/B |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Fogging（100℃） | < 2.0 | mg | DIN 75201 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| discharge | < 50.0 | µgC/g | VDA 277 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Mold temperature | 30 to 50 | °C | |
| Hold pressure | 30.0 to 60.0 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 3. 16 h |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |