Derakane® 411-45

About
DERAKANE 411-45 epoxy vinyl ester resin is based on bisphenol-A epoxy resin and has become an “industry standard” due to its wide range of end-use applications and ability to be used in a wide range of fabrication techniques. The raw materials used in the manufacture of this resin are listed as acceptable in FDA regulation Title 21 CFR 177.2420 for repeated use in contact with food, subject to user’s compliance with the prescribed limitations of that regulation. APPLICATIONS AND USE DERAKANE 411-45 resin is designed for use in fabricating FRP storage tanks, vessels, ducts and on-site maintenance projects, paticularly in chemical processing and pulp and paper operations. DERAKANE 411-45 resin is designed for ease of fabrication using hand lay-up, spray-up, filament winding, compression molding and resin transfer molding techniques, pultrusion and molded grating applications. DERAKANE 411-45 resin exhibits excellent mechanical properties over an entire service temperature range, very high damage resistance, down to -50°C (-58°F).&&

About

DERAKANE 411-45 epoxy vinyl ester resin is based on bisphenol-A epoxy resin and has become an “industry standard” due to its wide range of end-use applications and ability to be used in a wide range of fabrication techniques. The raw materials used in the manufacture of this resin are listed as acceptable in FDA regulation Title 21 CFR 177.2420 for repeated use in contact with food, subject to user’s compliance with the prescribed limitations of that regulation. APPLICATIONS AND USE DERAKANE 411-45 resin is designed for use in fabricating FRP storage tanks, vessels, ducts and on-site maintenance projects, paticularly in chemical processing and pulp and paper operations. DERAKANE 411-45 resin is designed for ease of fabrication using hand lay-up, spray-up, filament winding, compression molding and resin transfer molding techniques, pultrusion and molded grating applications. DERAKANE 411-45 resin exhibits excellent mechanical properties over an entire service temperature range, very high damage resistance, down to -50°C (-58°F).&&

Product Description
Generic	乙烯基酯
Material Status	Commercial: Active
Features	Good flexibility,Alkali resistant,Corrosion Resistant,Food contact compliance,Acidproof
Availabilitys	Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.12	g/cm³	ISO 1183
Solution viscosity	495	mPa·s
styrene content	45	%

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
1.8 MPa, unannealed	102	℃	ASTM D648，ISO 75-2/A

Supplementary information	Nominal value	Unit	Test method
Volume contraction	8.3	%

MECHANICAL	Nominal value	Unit	Test method
Babbitt hardness	35		ASTM D2583
Tensile modulus
—	3310	MPa	ASTM D638
—	3300	MPa	ISO 527-2
tensile strength
—	82.0	MPa	ASTM D638
—	81.0	MPa	ISO 527-2
Tensile strain
yield	5.0 to 6.0	%	ASTM D638 , ISO 527-2
Bending modulus	3100	MPa	ASTM D790 , ISO 178
bending strength	124	MPa	ASTM D790，ISO 178

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.