Devcon Brushable Ceramic Blue/Red

About
A brushable, high performance ceramic-filled epoxy for sealing, protecting and repairing surfaces subject to erosion, corrosion and wear. Intended Use: Seal and protect new equipment exposed to erosion and corrosion; protect pump casings, impeller blades, gate valves, water boxes, and fan blades; rebuild heat exchangers, tube sheets, and other water circulating equipment; top coat for providing exceptionally smooth surface to repaired surfaces Product features: Approved for use in meat and poultry plants (red only) Excellent chemical resistance Temperature resistance to 350°F Applies easily with short-bristle brush or roller Low viscosity, self-leveling liquid&&

About

A brushable, high performance ceramic-filled epoxy for sealing, protecting and repairing surfaces subject to erosion, corrosion and wear. Intended Use: Seal and protect new equipment exposed to erosion and corrosion; protect pump casings, impeller blades, gate valves, water boxes, and fan blades; rebuild heat exchangers, tube sheets, and other water circulating equipment; top coat for providing exceptionally smooth surface to repaired surfaces Product features: Approved for use in meat and poultry plants (red only) Excellent chemical resistance Temperature resistance to 350°F Applies easily with short-bristle brush or roller Low viscosity, self-leveling liquid&&

Product Description
Supplier	Devcon
Generic	环氧树脂
Material Status	Commercial: Active
Features	Low Viscosity,Solvent resistance
Availabilitys	North America

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.62	g/cm³
Specific volume	0.618	cm³/g
Shrinkage rate
MD	0.20	%	ASTM D2566
Solid content
by Volume	100	%

Electrical performance	Nominal value	Unit	Test method
Dielectric constant
1 MHz	3.87		ASTM D150

Supplementary information	Nominal value	Unit	Test method
Salt Spray	6.8	month
Heat resistant temperature
Dry	177	℃
Wet	66	℃
Tensile shear strength	13.8	MPa	ASTM D1002

Uncured Properties	Nominal value	Unit	Test method
Curing time	16	hr

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D	90		ASTM D2240
bending strength	55.2	MPa	ASTM D790
compressive strength	105	MPa	ASTM D695

THERMAL	Nominal value	Unit	Test method
Linear coefficient of thermal expansion
MD	3.4E-5	1/℃	ASTM D696
Thermosetting components
Component A	按容量计算的混合比: 3.4 按重量计算的混合比: 5.6
Component B	按容量计算的混合比: 1.0 按重量计算的混合比: 1.0
storage stability
24 ℃	40	min
Thermosetting mixed viscosity	32000	cP

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.