| About |
|---|
| DIALAC® AVR300 is an Acrylonitrile Styrene Acrylate (ASA) material. It is available in Asia Pacific or North America for injection molding. Important attributes of DIALAC® AVR300 are: Flame Rated RoHS Compliant&& |
| Product Description | |
|---|---|
| Supplier | Techno |
| Generic | ASA |
| Material Status | Commercial: Active |
| Features | V-0 |
| Availabilitys | North America,Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.21 | g/cm³ | ISO 1183 |
| Melt Volume Rate | |||
| 220℃，10 kg | 12.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| MD：23℃ | 0.60 to 0.80 | % | ISO 294-4 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179 | ||
| -30℃ | 5.0 | kJ/m² | ISO 179 |
| 23℃ | 12 | kJ/m² | ISO 179 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 71.0 | ℃ | ISO 75-2/Af |
| Linear coefficient of thermal expansion | |||
| MD | 1.0E-4 | 1/℃ | ISO 11359-2 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 2.20 mm | V-0 | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 86 | ISO 2039-2 | |
| Tensile modulus | |||
| 23℃ | 1750 | MPa | ISO 527-2 |
| tensile strength | |||
| 23℃ | 36.0 | MPa | ISO 527-2 |
| Bending modulus | |||
| 23℃ | 1850 | MPa | ISO 178 |
| bending strength | |||
| 23℃ | 55.0 | MPa | ISO 178 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 85 to 90 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Barrel rear temperature | 150 to 190 | °C | |
| Barrel middle temperature | 170 to 210 | °C | |
| Barrel front temperature | 180 to 220 | °C | |
| Nozzle temperature | 170 to 210 | °C | |
| Processing (melt) temperature | 200 to 230 | °C | |
| Mold temperature | 50 to 60 | °C | |
| Injection pressure | 70.0 to 130 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |