| About |
|---|
| DIALAC® SE20 is an Acrylonitrile Ethylene Styrene (AES) material. It is available in Asia Pacific or North America. Important attributes of DIALAC® SE20 are: Flame Rated RoHS Compliant&& |
| Product Description | |
|---|---|
| Supplier | Techno |
| Generic | 丙烯腈-EPDM-苯乙烯共聚物 |
| Material Status | Commercial: Active |
| Availabilitys | North America,Asia Pacific |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.05 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| MD：2.0 mm | 0.70 | % | ISO 294-4 |
| Melt Flow Rate | |||
| 220℃，10.0kg | 11.00 | g/10min | ISO 1133 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, annealed | 82 | ℃ | ISO 75-2/Af |
| Linear coefficient of thermal expansion | |||
| MD | 9.0E-5 | 1/℃ | ISO 11359-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volumetric resistance | 1.0E+15 | Ω.cm | IEC 60093 |
| Insulation strength | |||
| 32 | KV/mm | IEC 60243-1 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50mm | HB | UL-94 | |
| 3.00mm | HB | UL-94 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 13 | kJ/m² | ISO 179/1eA |
| -30℃ | 5.0 | kJ/m² | ISO 179/1eA |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | 107 | R 级 | ISO 2039-2 |
| tensile strength | |||
| 23℃ | 47 | MPa | ISO 527-2 |
| Tensile modulus | |||
| 23℃ | 2350 | MPa | ISO 527-2 |
| bending strength | |||
| 23℃ | 76 | MPa | ISO 178 |
| Bending modulus | |||
| 23℃ | 2600 | MPa | ISO 178 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80 -85 | °C | |
| Drying time | 3.0-4.0 | Hr | |
| Injection temperature | |||
| Rear barrel temperature | 150-190 | °C | |
| Central temperature of the barrel | 170-210 | °C | |
| Barrel front temperature | 180-220 | °C | |
| Die temperature | 170-210 | °C | |
| Mold temperature | 50-60 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |