Dow ENDURANCE™ HFDB-4201 VC

About
DOW ENDURANCE™ HFDB-4201 VC is a long-life, unfilled, crosslinkable, low density polyethylene insulation compound designed for distribution and transmission power cable insulation applications. It has a very low level of contamination and bears the designation Very Clean (VC). DOW ENDURANCE™ HFDB-4201 VC has been designed to have a low level of additive bloom for a long storage life, low dusting and an enhanced degree of scorch retardance for long production run lengths during cable manufacture. DOW ENDURANCE™ HFDB-4201 VC is recommended for the insulation of power distribution and transmission cables rated at less than 150 kV with stresses less than 7 kV/mm. Specifications DOW ENDURANCE™ HFDB-4201 VC is designed for use in power distribution and transmission cables. Cables insulated with DOW ENDURANCE™ HFDB-4201VC, using sound commercial manufacturing practice, would be expected to meet the latest editions of the following specifications and regulations: IEC 60502, 60840 GB/T 12706 ANSI/ICEA: S-94-649, S-97-682, S-93-639/NEMA WC74 CENELEC HD 620 S2 BSI BS 6622, 7870-4 Applicable to USA manufactured product only.

About

DOW ENDURANCE™ HFDB-4201 VC is a long-life, unfilled, crosslinkable, low density polyethylene insulation compound designed for distribution and transmission power cable insulation applications. It has a very low level of contamination and bears the designation Very Clean (VC). DOW ENDURANCE™ HFDB-4201 VC has been designed to have a low level of additive bloom for a long storage life, low dusting and an enhanced degree of scorch retardance for long production run lengths during cable manufacture. DOW ENDURANCE™ HFDB-4201 VC is recommended for the insulation of power distribution and transmission cables rated at less than 150 kV with stresses less than 7 kV/mm. Specifications DOW ENDURANCE™ HFDB-4201 VC is designed for use in power distribution and transmission cables. Cables insulated with DOW ENDURANCE™ HFDB-4201VC, using sound commercial manufacturing practice, would be expected to meet the latest editions of the following specifications and regulations: IEC 60502, 60840 GB/T 12706 ANSI/ICEA*: S-94-649, S-97-682, S-93-639/NEMA WC74 CENELEC HD 620 S2 BSI BS 6622, 7870-4 *Applicable to USA manufactured product only.

Product Description
Supplier	DOW
Generic	LDPE
Material Status	Commercial: Active
Availabilitys	Asia Pacific,Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.920	g/cm³	ASTM D792
humidity	< 200	ppm	Internal Method

MECHANICAL	Nominal value	Unit	Test method
Tensile strength	20.0	MPa	ASTM D638
Tensile strain
fracture	500	%	ASTM D638

Aging performance	Nominal value	Unit	Test method
Change in Tensile Properties – （7 days@320°F/150°C）	< 25	%	ASTM D638

THERMAL	Nominal value	Unit
thermosetting
Under load: 200 ℃	< 100	%
Elongation without load: 200 ℃	< 5.0	%

Electrical performance	Nominal value	Unit	Test method
Volume resistivity
23℃	> 1.0E+16	ohms·cm	ASTM D257
Dielectric strength
3.18 mm, Method A (Short term)	> 30	kV/mm
3.18 mm, Method B (step-by-step)	> 23	kV/mm
3.18 mm, Method C (flow rate rise rate)	> 39	kV/mm
Dielectric constant
23℃	2.30		ASTM D150
Dissipation factor
23℃	3.0E-4		ASTM D150

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.