| About |
|---|
| Linear Low Density Polyethylene Outstanding tear strength, impact strength and toughness For high performance cast film applications Complies with U.S. FDA 21 CFR 177.1520 (c) 3.2a. Complies with Canadian HPFB No Objection (With Limitations) Complies with U.S. FDA-DMF Complies with U.S. FDA-U.S. USP Complies with EU, No 10/2011 Complies with Japan Hygienic Olefin and Styrene Plastics Association Consult the regulations for complete details.&& |
| Product Description | |
|---|---|
| Supplier | DOW |
| Generic | Linear low density polyethylene |
| Material Status | Commercial: Active |
| Availabilitys | North America,Asia Pacific |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.919 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 6.0 | g/10min | ASTM D1238 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 25 | µm | |
| Membrane puncture resistance | 10.7 | J/cm³ | Internal Method |
| Membrane strength | ASTM D882 | ||
| MD：25 µm | 131 | J/cm³ | ASTM D882 |
| TD：25 µm | 132 | J/cm³ | ASTM D882 |
| tensile strength | ASTM D882 | ||
| MD, yield, 25 µ m | 11.1 | MPa | ASTM D882 |
| TD, yield, 25 µ m | 10.4 | MPa | ASTM D882 |
| MD, fracture, 25 µ m | 51.1 | MPa | ASTM D882 |
| TD, fracture, 25 µ m | 36.3 | MPa | ASTM D882 |
| Tensile strain | ASTM D882 | ||
| MD, fracture, 25 µ m | 610 | % | ASTM D882 |
| TD, fracture, 25 µ m | 770 | % | ASTM D882 |
| Drop hammer impact | |||
| 25 µm | 140 | g | ASTM D1709-A |
| Elmandorf tear strength | ASTM D1922 | ||
| MD：25 µm | 270 | g | ASTM D1922 |
| TD：25 µm | 610 | g | ASTM D1922 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | 97.8 | ℃ | ASTM D1525 |
| Melting temperature | |||
| DSC | 124 | ℃ | Internal Method |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 45°，25.4 µm | 96 | ASTM D2457 | |
| Haze | |||
| 25.4 µm | 0.80 | % | ASTM D1003 |
| Notes |
|---|
| 1. With limitations |
| 2. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |