| About |
|---|
| Durastar™ DS1010 polymer contains a mold release. It has excellent appearance and clarity. Its most outstanding features are chemical resistance and excellent processing characteristics. Exposure to aromatic oils often causes crazing or actual fracture of many polymer resins, but DS1010 maintains its physical properties when exposed to these oils, and its appearance is virtually unchanged. Easy to process, it flows readily, fills intricate molds, and is well suited for thick-wall applications. Under existing United States Food and Drug Administration (FDA) regulations, Durastar™ DS1010 may be used in food contact articles which comply with the specifications and conditions of use in 21 CFR 177.1240. This product is certified to ANSI/NSF Standard 51.&& |
| Product Description | |
|---|---|
| Supplier | Eastman |
| Generic | 热塑性聚酯 |
| Material Status | Commercial: Active |
| Features | Excellent Processability,Good Clarity,Good surface appearance,High impact resistance,Good liquidity,Quick molding cycle,Good stripping performance,Food contact compliance,Solvent resistance |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.20 | g/cm³ | ASTM D792 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Transmittance | 91 | % | ASTM D1003 |
| Haze μ M | 0.3 | % | ASTM D1003 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 75 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 65 | ℃ | ASTM D648 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50mm | HB | UL-94 | |
| 3.00mm | HB | UL-94 | |
| 3.00mm | V-2 | UL 94 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 80 | J/m | ASTM D256 |
| -40℃ | 40 | J/m | ASTM D256 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | 103 | R 级 | ASTM D785 |
| tensile strength | |||
| 23℃ | 47 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 23 ℃ | 300 | % | ASTM D638 |
| bending strength | |||
| 23℃ | 69 | MPa | ASTM D790 |
| Bending modulus | |||
| 23℃ | 2000 | MPa | ASTM D790 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 70 | °C | |
| Drying time | 3.0-4.0 | Hr | |
| Injection temperature | |||
| Mold temperature | 20-40 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |