| About |
|---|
| DuraStar™ Polymer MN610 Natural polymer has excellent appearance and is nearly water-clear. Benefits include toughness, chemical resistance, and excellent processing characteristics. MN610 has very good toughness as shown by Izod impact resistance. Easy to process, it flows readily and fills intricate molds. This product does not contain a mold release.&& |
| Product Description | |
|---|---|
| Supplier | Eastman |
| Generic | 热塑性聚酯 |
| Material Status | Commercial: Active |
| Features | Excellent Processability,Good Clarity,Good flexibility,Good surface appearance,Good liquidity,Solvent resistance |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.20 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| MD | 0.2 | % | ASTM D995 |
| TD | 0.6 | % | ASTM D995 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Transmittance | 89-91 | % | ASTM D1003 |
| Haze μ M | 0.30 | % | ASTM D1003 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 74 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 65 | ℃ | ASTM D648 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | 103 | M 级 | ASTM D785 |
| tensile strength | |||
| 23℃ | 51 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 23 ℃ | 300 | % | ASTM D638 |
| bending strength | |||
| 23℃ | 69 | MPa | ASTM D790 |
| Bending modulus | |||
| 23℃ | 2000 | MPa | ASTM D790 |
| Instrument drop dart impact | 578.00 | J | ASTM D3763 |
| Instrument drop dart impact | 505.92 | J | ASTM D3763 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 80 | J/m | ASTM D256 |
| -40℃ | 40 | J/m | ASTM D256 |
| Notched impact strength of cantilever beam | |||
| 23℃ | NB | J/m | ASTM D4812 |
| -40℃ | NB | J/m | ASTM D4812 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 70 | °C | |
| Drying time | 3.0 | Hr | |
| Injection temperature | |||
| Rear barrel temperature | 230-280 | °C | |
| Central temperature of the barrel | 230-280 | °C | |
| Barrel front temperature | 230-280 | °C | |
| Die temperature | 230-280 | °C | |
| Mold temperature | 25-30 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |