| About |
|---|
| Product Description | |
|---|---|
| Supplier | LANXESS |
| Generic | PA6 |
| Material Status | Commercial: Negative |
| Features | Flame Characteristics,Halogen free |
| Availabilitys | Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.423 | g/cm³ | ISO 1183 |
| Mold Shrinkage | |||
| TD：270℃，2.0 mm | 0.70 | % | ISO 294-4 |
| MD：270℃，2.0 mm | 0.20 | % | ISO 294-4 |
| Post shrinkage | |||
| TD：120℃，2.0 mm | 0.10 | % | ISO 294-4 |
| MD：120℃，2.0 mm | 0.10 | % | ISO 294-4 |
| Water Absorption | |||
| Saturation, 23 ℃ | 4.6 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 1.5 | % | ISO 62 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Impact strength of simply supported beams | |||
| 23℃ | 60 | KJ/m² | ISO 179-1eU |
| -30℃ | 55 | KJ/m² | ISO 179-1eU |
| Charpy Notched Impact Strength | |||
| 23℃ | ＜10 | kJ/m² | ISO 179/1eA |
| -30℃ | ＜10 | kJ/m² | ISO 179/1eA |
| Izod Impact strength of cantilever beam | |||
| 23℃ | 55 | kJ/m² | ISO 180-1U |
| Izod Notched Impact strength | |||
| 23℃ | ＜10 | KJ/m² | ISO 180-1A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | |||
| 10 °C/min | 220 | ℃ | ISO 11357-1,-3 |
| Hot deformation temperature HDT | |||
| 0.45 MPa, unannealed | 219 | ℃ | ISO 75-1,-2 |
| 1.8 MPa, unannealed | 205 | ℃ | ISO 75-1,-2 |
| Vicat Softening Temperature | |||
| 50 N; 120 °C/h | 212 | ℃ | ISO 306 |
| Coeff. of linear thermal expansion | |||
| MD：23~55℃ | 0.2 | ×10-4/K | ISO 11359-1,-2 |
| TD：23~55℃ | 0.8 | ×10-4/K | ISO 11359-1,-2 |
| ELECTRICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric Constant | |||
| 100 Hz | 4.5 | IEC 60250 | |
| 1 MHz | 3.9 | IEC 60250 | |
| Dissipation Factor | |||
| 100 Hz | 0.026 | IEC 60250 | |
| 1 MHz | 0.016 | IEC 60250 | |
| Volume Resistance | 7.3E+13 | ohm·m | IEC 60093 |
| Dielectric Strength | |||
| 1 mm | 30 | kV/mm | IEC 60243-1 |
| Compared Tracking Index | |||
| Solution A | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| UL flame retardant rating | |||
| 1.50mm | V-0 | class | UL 94 |
| 0.75mm | V-0 | class | UL 94 |
| Flame Class Rating | |||
| 1.5mm | 5VA | class | UL 94 |
| Oxygen Index | |||
| Solution A | 32 | % | ISO 4589-2 |
| Glow Wire Flammability Index GWFI | |||
| 0.40 mm | 960 | ℃ | IEC 60695-2-12 |
| 0.75 mm | 960 | ℃ | IEC 60695-2-12 |
| 1.5 mm | 960 | ℃ | IEC 60695-2-12 |
| 3.0 mm | 960 | ℃ | IEC 60695-2-12 |
| Glow Wire Ignitability Temperature (GWIT) | |||
| 0.4 mm | 775 | ℃ | IEC 60695-2-13 |
| 0.75 mm | 775 | ℃ | IEC 60695-2-13 |
| 1.5 mm | 775 | ℃ | IEC 60695-2-13 |
| 3 mm | 800 | ℃ | IEC 60695-2-13 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile Modulus | |||
| 1 mm/min | 10300 | MPa | ISO 527-1,-2 |
| Tensile Strength | |||
| 5 mm/min, fracture | 130 | MPa | ISO 527-1,-2 |
| Tensile Strain | |||
| 5 mm/min, fracture | 3 | % | ISO 527-1,-2 |
| Flexural Modulus | |||
| 2 mm/min | 10200 | MPa | ISO 178-A |
| Flexural Strength | |||
| 2 mm/min | 230 | MPa | ISO 178-A |
| Flexural Strain | |||
| 2 mm/min | 3.1 | % | ISO 178-A |
| Process Conditions | |||
|---|---|---|---|
| Injection Molding | Nominal value | Unit | Test method |
| Drying Temperature | 80 | ℃ | |
| Drying Time | 2.0 to 6.0 | hr | |
| Melt Temperature | 250 to 280 | ℃ | |
| Mold Temperature | 70 to 90 | ℃ | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |