| About |
|---|
| Durethan® DPAKV30FN00 000000 DUS013 (Dry) PA 66, 30 % glass fibers, injection molding, halogen free flame retardant, optimized for laser marking (1064nm)&&Durethan® DPAKV30FN00 000000 DUS013 PA 66, 30 % glass fibers, injection molding, halogen free flame retardant, optimized for laser marking (1064nm)&&Durethan® DPAKV30FN00 000000 DUS013 PA 66, 30 % glass fibers, injection molding, halogen free flame retardant, optimized for laser marking (1064nm)&& |
| Product Description | |
|---|---|
| Supplier | LANXESS |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | Halogen free,Flame Characteristics,Laser engraving |
| Availabilitys | Africa & Middle East ,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.43 | g/cm³ | |
| Shrinkage rate | |||
| TD：120℃，2.0 mm | 0.10 | % | |
| TD：270℃，2.0 mm | 0.70 | % | |
| MD：120℃，2.0 mm | 0.10 | % | |
| MD：270℃，2.0 mm | 0.20 | % | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 23℃ | 10500 | MPa | |
| tensile strength | |||
| Fracture, 23 ℃ | 120 | MPa | |
| Tensile strain | |||
| Fracture, 23 ℃ | 2.5 | % | |
| Bending modulus | |||
| 23℃ | 9300 | MPa | |
| bending strength | |||
| 23℃ | 190 | MPa | |
| 3.50% strain, 23 ℃ | — | MPa | |
| Bending strain | 2.7 | % |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 10 | kJ/m² | |
| Notched impact strength of cantilever beam | |||
| 23℃ | 45 | kJ/m² |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | > 250 | ℃ | |
| 1.8 MPa, unannealed | 224 | ℃ | |
| Vicat Softening Temp | 240 | ℃ | |
| Melting temperature | 260 | ℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 3.0E+16 | ohms | |
| Volume resistivity | |||
| 23℃ | 5.0E+15 | ohms·cm | |
| Dielectric strength | |||
| 23 ℃，1 mm | 39 | kV/mm | |
| Relative permittivity | |||
| 23℃，100 Hz | 3.90 | ||
| 23℃，1 MHz | 3.70 | ||
| Dissipation factor | |||
| 23℃，100 Hz | 8.0E-3 | ||
| 23℃，1 MHz | 0.012 | ||
| Compared to the leakage tracing index | |||
| Solution A | 600 | V |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 0.40 mm | V-0 | ||
| 1.50 mm | V-0 | ||
| Glowing wire flammability index | |||
| 0.75 mm | 960 | ℃ | |
| 1.5 mm | 960 | ℃ | |
| 3.0 mm | 960 | ℃ | |
| Igniting temperature of the hot wire | |||
| 0.75 mm | 725 | ℃ | |
| 1.5 mm | 725 | ℃ | |
| 3 mm | 725 | ℃ |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| ISO Shortname | ISO 1874-PA 66, GFHR, 14-100, GF30 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying Temperature – Dry Air Dryer | 80 | °C | |
| Drying Time – Dry Air Dryer | 2.0 to 6.0 | hr | |
| Processing (melt) temperature | 265 to 285 | °C | |
| Mold temperature | 80 to 100 | °C | |
| Residual Moisture Content | 0.030 to 0.070 | % | Karl Fisher |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 60x60x2mm, 4 hr |
| 3. 60x60x2mm, 80°C MT, 600 bar |
| 4. 0.079 in/min |
| 5. 2 mm/min |
| 6. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |