| About |
|---|
| EM10000 is semi-crystalline biodegradable, aliphatic bio-polyester designed for use in film applications. EM10000 is certificated to meet EU direct food contact, EN13432 and OK Home compost standards for biodegradable plastics. Typical applications: Blown and cast film applications, such as paper coating&& |
| Product Description | |
|---|---|
| Supplier | Ecomann |
| Generic | PHA |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Excellent Processability,Good flexibility,Good surface appearance,Good heat sealing,High impact resistance,Hydrolysis stability,Good Printability,Biodegradable,Food contact compliance,Good bond,Hypocrystalline,Aliphatic series,Compostable,Poor moisture permeability |
| Availabilitys | Asia Pacific |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.24 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 170℃，2.16kg | 3.0 | g/10min | ASTM D1238 |
| Water absorption rate | |||
| balance | < 0.40 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | 13.0 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 550 | % | ASTM D638 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| Oxygen transfer rate | |||
| 40℃，90% RH，70 µm | 160 | cm³/m²/24 hr | |
| Water vapor transmittance | |||
| 25℃，90% RH，70 µm | 13 | g/m²/24 hr |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | 85.0 | ℃ | ASTM D1525 2 |
| Melting temperature | 120 to 140 | ℃ | DSC |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Yellowness index | 60 | YI | Internal Method |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Blow molding barrel temperature | |||
| Compression section | 110 to 125 | ℃ | |
| Feed Temperature | 100 to 115 | ℃ | |
| Melting Section | 110 to 125 | ℃ | |
| Blow molding mold temperature | 120 to 135 | ℃ | |
| Blow Molding Melt Temperature | 120 to 140 | ℃ | |
| Blow Molding Screw Speed | 30 to 50 | rpm |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 80 | °C | |
| Drying time | 3.0 | hr | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Rate B (120°C/h), Loading 1 (10 N) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |