Ecovio® FT2341

About
ecovio® FT2341 is our new biodegradable film product based on renewable resources. It is basically a compound of our biodegradable, aliphatic-aromatic copolyester grades ecoflex® F and ecoflex® FS and a small amount of polylactic acid (PLA). ecovio® FT2341 has a biobased content of 34%. Due to its outstanding mechanical strength ecovio® FT2341 offers a great down gauging potential needed for very thin film applications like T-shirt, organic waste and fruit & vegetable bags etc. ecovio® FT2341 does not contain slip agents. ecoflex® slip masterbatches have to be used to tailor the sliding properties required for easy processing on film extrusion and film conversion equipment.&&

About

ecovio® FT2341 is our new biodegradable film product based on renewable resources. It is basically a compound of our biodegradable, aliphatic-aromatic copolyester grades ecoflex® F and ecoflex® FS and a small amount of polylactic acid (PLA). ecovio® FT2341 has a biobased content of 34%. Due to its outstanding mechanical strength ecovio® FT2341 offers a great down gauging potential needed for very thin film applications like T-shirt, organic waste and fruit & vegetable bags etc. ecovio® FT2341 does not contain slip agents. ecoflex® slip masterbatches have to be used to tailor the sliding properties required for easy processing on film extrusion and film conversion equipment.&&

Product Description
Supplier	BASF
Generic	PCTG
Material Status	Commercial: Negative
Features	Good Rigidity,Excellent Processability,Renewable resources,Aromatic,Biodegradable,Food contact compliance,Hypocrystalline,Aliphatic series,Good melt strength,Compostable,Good tear strength,Heat Stabilized
Availabilitys	North America,Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.36 to 1.40	g/cm³	ISO 1183
Apparent density	0.80	g/cm³	ISO 60
Melt Volume Rate
190℃，5 kg	2.50 to 7.50	cm³/10min	ISO 1133
Biomass content	34	%	ASTM D6866

film	Nominal value	Unit	Test method
film thickness
test	25	µm
Tensile modulus			ISO 527-3
MD, 25 µ m, blow molded film	270	MPa	ISO 527-3
TD, 25 µ m, blow molded film	160	MPa	ISO 527-3
tensile strength			ISO 527-3
MD, 25 µ m, blow molded film	24.0	MPa	ISO 527-3
TD, 25 µ m, blow molded film	21.0	MPa	ISO 527-3
Tensile strain			ISO 527-3
MD, fracture, 25 µ m, blow molded film	340	%	ISO 527-3
TD, fracture, 25 µ m, blow molded film	610	%	ISO 527-3
Drop hammer impact
25 µ m, blow molded film	150	g	ASTM D1709-A
Elmandorf tear strength			ISO 6383-2
MD: 25 µ m, blow molded film	4.9	N	ISO 6383-2
TD: 25 µ m, blow molded film	3.0	N	ISO 6383-2

THERMAL	Nominal value	Unit	Test method
Melting temperature			DSC
—	110 to 120	℃	DSC
—	140 to 155	℃	DSC

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.