| About |
|---|
| The Edgetek™ engineering thermoplastics compounds made with Eastman Tritan™ copolyester offer a wide range of performance and properties with the addition of reinforcing additives. By utilizing Eastman Tritan™ copolyester these compounds provide chemical resistance, clarity, heat resistance and BPA-free solutions.&& |
| Product Description | |
|---|---|
| Supplier | Polyone |
| Generic | PCTG |
| Material Status | Commercial: Active |
| Features | Good flexibility,Good Dimensional Stability,No BPA,Good tear strength,Heat Resistance, Good,Solvent resistance,High ESCR |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.33 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.20 to 0.30 | % | ASTM D955 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 3380 | MPa | ASTM D638 |
| tensile strength | ASTM D638 | ||
| yield | 51.7 | MPa | ASTM D638 |
| fracture | 40.7 | MPa | ASTM D638 |
| Tensile strain | ASTM D638 | ||
| yield | 5.0 | % | ASTM D638 |
| fracture | 30 | % | ASTM D638 |
| Bending modulus | 3030 | MPa | ASTM D790 |
| bending strength | 89.6 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23 ℃, 3.2mm, injection molding | 75 | J/m | ASTM D256-A |
| Notched impact strength of cantilever beam | |||
| 23 ℃, 3.2 mm, injection molding | 2100 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 0.45 MPa, unannealed, 3.2 mm | 112 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 3.2 mm | 103 | ℃ | ASTM D648 |
| Linear coefficient of thermal expansion | ASTM E831 | ||
| MD：-30~30℃ | 1.1E-4 | 1/℃ | ASTM E831 |
| TD：-30~30℃ | 1.4E-4 | 1/℃ | ASTM E831 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 88 | °C | |
| Drying time | 4.0 | hr | |
| Processing (melt) temperature | 266 to 282 | °C | |
| Mold temperature | 60 to 66 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Type I, 0.20 in/min |
| 3. 0.20 in/min |
| 4. 0.050 in/min |
| 5. Partial Break |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |