EMERGE™ PC 4330ECO

About
EMERGE PC 4330ECO Advanced Polycarbonate Resin contains 50% post consumer recycled (PCR) polycarbonate with IEEE 1680:2006 certified by TÜV Rheinland. Its color under the code of IC8800234 meets the stringent requirement of white. This resin also provides a property balance of flowability, ductility, stiffness and thermal resistance to meet the market needs on various applications in information technology equipment (ITE) and consumer electronics without painting or coating. Applications Packaging for ITE Electronic accessories Electrical appliances&&

About

EMERGE PC 4330ECO Advanced Polycarbonate Resin contains 50% post consumer recycled (PCR) polycarbonate with IEEE 1680:2006 certified by TÜV Rheinland. Its color under the code of IC8800234 meets the stringent requirement of white. This resin also provides a property balance of flowability, ductility, stiffness and thermal resistance to meet the market needs on various applications in information technology equipment (ITE) and consumer electronics without painting or coating. Applications Packaging for ITE Electronic accessories Electrical appliances&&

Product Description
Supplier	Trinseo
Generic	Polycarbonate
Material Status	Commercial: Active
Features	Good Rigidity,Ductility,Good liquidity,High Heat Resistance
Availabilitys	Asia Pacific
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.26	g/cm³	ASTM D792
Melt Flow Rate
300℃，1.20kg	23	g/10min	ASTM D1238
Shrinkage rate
MD	0.50 to 0.70	%	ASTM D955

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23 ℃, 3.2mm, injection molding	640	J/m	ASTM D256

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature			ASTM D648
0.45 MPa, unannealed	131	℃	ASTM D648
1.8 MPa, unannealed	119	℃	ASTM D648

MECHANICAL	Nominal value	Unit	Test method
Shore hardness			ASTM D2240
Shaw A, 3.20 mm	99		ASTM D2240
Shaw D, 3.20 mm, injection molded	86		ASTM D2240
Tensile modulus
3.20 mm, injection molded	2200	MPa	ASTM D638
tensile strength
Yield, 3.20 mm, injection molding	62.0	MPa	ASTM D638
Tensile strain
Fracture, 3.20 mm, injection molded	110	%	ASTM D638
Bending modulus
3.20 mm, injection molded	2450	MPa	ASTM D790
bending strength
3.20 mm, injection molded	96.0	MPa	ASTM D790

Process Conditions
injection	Nominal value	Unit	Test method
Drying temperature	120	°C
Drying time	3.0 to 4.0	hr
Processing (melt) temperature	280 to 300	°C
Mold temperature	60 to 90	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.