| About |
|---|
| EMERGE™ PC 8830-5 LT Advanced Resin is a transparent, ignition resistant PC resin that contains no chlorinated or brominated or phosphorous based flame retardant, designed to meet the German norm DIN VDE-0472/Part 815 on halogens. This resin combines good mechanical and heat resistant properties, ensuring longer sustained aesthetics and mechanical resistance to the applications. EMERGE ™ PC 8830-5LT has a UL 94 V-0 rating at 1.0 mm, 5VA @ 3mm and UL746C f1 rating. The material contains mould release agent and UV stabilizer. Applications LED Tube, LED lamp Lens Electrical parts&& |
| Product Description | |
|---|---|
| Supplier | Trinseo |
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Features | Good surface appearance,Halogen free,Flame Characteristics,Low to no phosphorus content,Heat Resistance, Good,V-0,5VA,5VB |
| Availabilitys | Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.20 | g/cm³ | ISO 1183/B |
| Melt Flow Rate | |||
| 300℃，1.20kg | 5.0 | g/10min | ISO 1133 |
| Shrinkage rate | ISO 294-4 | ||
| TD | 0.70 | % | ISO 294-4 |
| MD | 0.70 | % | ISO 294-4 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2400 | MPa | ISO 527-1-2 |
| tensile strength | ISO 527-2/50 | ||
| Yield, 3.20 mm, injection molding | 64.0 | MPa | ISO 527-2/50 |
| Fracture, 3.20 mm, injection molded | 59.0 | MPa | ISO 527-2/50 |
| Tensile strain | ISO 527-2/50 | ||
| Yield, 3.20 mm, injection molding | 6.3 | % | ISO 527-2/50 |
| Fracture, 3.20 mm, injection molded | 110 | % | ISO 527-2/50 |
| Bending modulus | |||
| 3.20 mm, injection molded | 2240 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23 ℃, injection molding | 16 | kJ/m² | ISO 179/1eA |
| Impact strength of cantilever beam notch | |||
| 23 ℃, injection molding | 13 | kJ/m² | ISO 180-A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 136 | ℃ | ISO 75-2/B |
| 1.8 MPa, unannealed | 128 | ℃ | ISO 75-2/A |
| Vicat Softening Temp | |||
| — | 151 | ℃ | ISO 306/A120 |
| B50 | 143 | ℃ | ISO 306 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 1.00 mm | V-0 | UL 94 | |
| 2.50 mm | 5VB | UL 94 | |
| 3.00 mm | 5VA | UL 94 | |
| Glowing wire flammability index | IEC 60695-2-12 | ||
| 1.0 mm | 800 | ℃ | IEC 60695-2-12 |
| 1.5 mm | 960 | ℃ | IEC 60695-2-12 |
| 2.0 mm | 960 | ℃ | IEC 60695-2-12 |
| 3.0 mm | 960 | ℃ | IEC 60695-2-12 |
| Igniting temperature of the hot wire | IEC 60695-2-13 | ||
| 1 mm | 825 | ℃ | IEC 60695-2-13 |
| 1.5 mm | 825 | ℃ | IEC 60695-2-13 |
| 2 mm | 825 | ℃ | IEC 60695-2-13 |
| 3 mm | 825 | ℃ | IEC 60695-2-13 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Transmittance | |||
| 1000 µm | 90.0 | % | |
| 2000 µm | 88.0 | % |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 120 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Barrel rear temperature | 280 to 300 | °C | |
| Barrel middle temperature | 280 to 310 | °C | |
| Barrel front temperature | 290 to 320 | °C | |
| Nozzle temperature | 290 to 320 | °C | |
| Mold temperature | 60 to 100 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. This rating not intended to reflect hazards presented by this or any other material under actual fire conditions. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |