| About |
|---|
| Enflex V1050D TPV (thermoplastic vulcanizate) is a general purpose rigid black EPDM/PP compound available in both natural and black. This grade is design for injection molding, extrusion and blow molding applications requiring high rigidity with high heat resistance.&& |
| Product Description | |
|---|---|
| Generic | TPV |
| Material Status | Commercial: Negative |
| Features | Good Rigidity,Weather resistance is good,Excellent Processability,Alkali resistant,Good Dimensional Stability,Renewable resources,Ethanol tolerance,Acidproof,High Heat Resistance,Grease resistance,Ozone resistance,Solvent resistance,Resistance to detergents |
| Availabilitys | North America |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.950 | g/cm³ | ASTM D792 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ASTM D2240 | ||
| Shore D, 5 seconds, extrusion molding | 50 | ASTM D2240 | |
| Shore D, 5 seconds, injection molding | 51 | ASTM D2240 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| fracture | 25.0 | MPa | ASTM D412 |
| 100% strain | 11.0 | MPa | ASTM D412 |
| Tensile strain | |||
| fracture | 720 | % | ASTM D412 |
| tear strength | 102 | kN/m | ASTM D624 |
| Compression deformation | ASTM D395 | ||
| 70℃，22 hr | 70 | % | ASTM D395 |
| 125℃，70 hr | 90 | % | ASTM D395 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -30.0 | ℃ | ASTM D746 |
| Melting temperature | 158 | ℃ | ASTM D1238 |
| Dynamic Service Temperature | 130 | ℃ |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 82 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Recommended maximum moisture content | 0.080 | % | |
| Barrel rear temperature | 177 to 188 | °C | |
| Barrel middle temperature | 182 to 193 | °C | |
| Barrel front temperature | 188 to 199 | °C | |
| Nozzle temperature | 199 to 221 | °C | |
| Processing (melt) temperature | 199 to 232 | °C | |
| Mold temperature | 10 to 49 | °C | |
| Injection pressure | 5.17 to 8.96 | MPa | |
| Barrel temperature | 160 to 177 | °C | |
| Barrel 1 zone temperature | 171 to 191 | °C | |
| Barrel 2 zone temperature | 171 to 191 | °C | |
| Barrel 3 zone temperature | 171 to 191 | °C | |
| Barrel 4 zone temperature | 171 to 191 | °C | |
| Barrel 5 zone temperature | 171 to 191 | °C | |
| Connector temperature | 191 to 210 | °C | |
| Melt temperature | 191 to 199 | °C | |
| Nozzle temperature | 191 to 210 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |