ENFLEX VO-564-65A

About
This polyolefin based dynamically vulcanized TPE-V compound is flame retardant and dio1ine free. ENFLEX® series are competely recyclable and can be processed with conventional thermoplastics machinery Additive Packages : F / Heat and UV stabilizer and Flame Retardant Key Features : V0 at 1,6 mm acoording to UL94 (internally tested) Excellent ozone, UV and weathering resistance Rubberlike elasticity in a wide temperature range Colorable with proper MB (PE, PP, etc. based) Process Method : Extrusion, coextrusion, sheet extrusion, injection/multi injection molding Uses : Automotive, construction, electrical&electronics, wire&cable, industrial applications&&

About

This polyolefin based dynamically vulcanized TPE-V compound is flame retardant and dio1ine free. ENFLEX® series are competely recyclable and can be processed with conventional thermoplastics machinery Additive Packages : F / Heat and UV stabilizer and Flame Retardant Key Features : V0 at 1,6 mm acoording to UL94 (internally tested) Excellent ozone, UV and weathering resistance Rubberlike elasticity in a wide temperature range Colorable with proper MB (PE, PP, etc. based) Process Method : Extrusion, coextrusion, sheet extrusion, injection/multi injection molding Uses : Automotive, construction, electrical&electronics, wire&cable, industrial applications&&

Product Description
Generic	TPV
Material Status	Commercial: Active
Features	Weather resistance is good,High elastic,Renewable resources,Flame Characteristics,Ozone resistance,Solvent resistance,Heat Stabilized,Good coloring
Availabilitys	Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.35	g/cm³	ISO 1183/A

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shore A, 3 seconds	65		ISO 868

elastic body	Nominal value	Unit	Test method
tensile strength
fracture	5.30	MPa	ISO 37
100% strain	2.50	MPa
300% strain	3.20	MPa
Tensile strain
fracture	580	%	ISO 37
tear strength
TD	32	kN/m	ISO 34-1
Compression deformation
23℃，72 hr	24	%
70℃，22 hr	36	%

THERMAL	Nominal value	Unit
Embrittlement temperature	-55.0	℃
Operating temperature
Dynamic	110	℃
Static	135	℃

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
1.60 mm	V-0		Internal Method

Process Conditions
injection	Nominal value	Unit	Test method
Extrusion	Nominal value	Unit	Test method
Drying temperature	80 to 90	°C
Drying time	2.0	hr
Hopper temperature	170 to 180	°C
Barrel middle temperature	180 to 190	°C
Barrel front temperature	190 to 200	°C
Nozzle temperature	200 to 210	°C
Processing (melt) temperature	210 to 220	°C
Mold temperature	10 to 50	°C
Drying temperature	80 to 90	°C
Drying time	2.0	hr
Barrel 1 zone temperature	170 to 190	°C
Barrel 3 zone temperature	180 to 195	°C
Barrel 5 zone temperature	195 to 205	°C
Connector temperature	200 to 210	°C
Nozzle temperature	200 to 220	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.