| About |
|---|
| DESCRIPTION: Epocast® 1629-A/B epoxy syntactic is a beige-tan, self-extinguishing, ultra-low density system for edge reinforcing of honeycomb structures. It can be extruded or spread with a putty knife and resists slumping on vertical surfaces. Epocast® 1629-A/B epoxy syntactic sands and machines easily when cured. It is a non-PBDE containing material and can be used as a replacement for Epocast® 87005 A/B-80 epoxy syntactic, Epocast® 87005 A/B-60 epoxy syntactic, Epocast® 87269 A/B epoxy syntactic, Epocast® 87005 A/B-61 epoxy syntactic, and Epocast® 87005 A/BE- 60 epoxy syntactic.&& |
| Product Description | |
|---|---|
| Supplier | Huntsman |
| Generic | 环氧树脂 |
| Material Status | Commercial: Active |
| Features | Self-extinguishing,Low density |
| Availabilitys | North America |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | ASTM D1622 | ||
| — | 0.420 | g/cm³ | ASTM D1622 |
| — | 0.480 | g/cm³ | ASTM D1622 |
| — | 0.520 | g/cm³ | ASTM D1622 |
| viscosity | ASTM D2196 | ||
| — | Paste | ASTM D2196 | |
| — | Paste | ASTM D2196 | |
| — | Paste | ASTM D2196 | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Compression modulus | 1380 | MPa | ASTM D695 |
| compressive strength | |||
| 25℃ | 20.7 | MPa | ASTM D695 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| Burn length | 2.54 | cm | |
| Self extinguishing | 2.0 | sec |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Thermosetting components | |||
| resin | 按重量计算的混合比: 100 | ||
| Hardening method | 按重量计算的混合比: 50 | ||
| Gelation time | |||
| 75 gms，25℃ | 1.2 | hr | ASTM D2471 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Curing time | |||
| 25℃ | 2.0 | day | |
| Tensile Lap Shear（etched al/al，25℃） | 7.58 | MPa | ASTM D1002 |
| Weight gain | ASTM D543 | ||
| Distilled water：25℃ | 2.3 | % | ASTM D543 |
| Mil-M-5606，hydraulic fluid：25℃ | 1.5 | % | ASTM D543 |
| Mil-S-3136，Type III test fluid：25℃ | 0.60 | % | ASTM D543 |
| Skydrol 500-A：25℃ | 3.0 | % | ASTM D543 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Hardener |
| 3. System |
| 4. Resin |
| 5. 12-second vertical |
| 6. on immersion – 24 hrs |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |