| About |
|---|
| Type: Estane® 58630 is an 82A aromatic Polyether-Based Thermoplastic Polyurethane (TPU). Features: Good physical properties, hydrolysis resistance, low temperature performance and abrasion along with wide processing window for extrusion and low surface tack. Uses: Blown and flat die/cast film extrusion and cable jacketing.&& |
| Product Description | |
|---|---|
| Supplier | Lubrizol Advanced Materials |
| Generic | TPU-醚 |
| Material Status | Commercial: Active |
| Features | Excellent Processability,Hydrolysis stability,Antifreeze,Aromatic,Good wear resistance |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.13 | g/cm³ | ASTM D792 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile permanent deformation | |||
| 200% strain | 15 | % | ASTM D412 |
| tensile strength | ASTM D412 | ||
| Fracture, 0.762 mm | 41.4 | MPa | ASTM D412 |
| 100% strain, 0.762 mm | 5.20 | MPa | ASTM D412 |
| 300% strain, 0.762 mm | 7.60 | MPa | ASTM D412 |
| Tensile strain | |||
| Fracture, 0.762 mm | 640 | % | ASTM D412 |
| tear strength | |||
| 0.762 mm | 69.6 | kN/m | ASTM D624 |
| cracking | 23 | kN/m | ASTM D470 |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume change | |||
| 23 ℃, 24 hours in water | 2.1 | % | ASTM D471 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Glass transition temperature | -50.0 | ℃ | DSC |
| Melting temperature | 120 | ℃ | DSC |
| Kofler Melting Temperature | 125 | ℃ | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore A, 5 seconds | 79 to 85 | ASTM D2240 | |
| Taber abraser | |||
| 1000 cycles, 1000 g, H-18 wheels | 60.0 | mg | ASTM D3389 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 104 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Barrel 1 zone temperature | 166 | °C | |
| Barrel 2 zone temperature | 171 | °C | |
| Barrel 3 zone temperature | 177 | °C | |
| Barrel 4 zone temperature | 182 | °C | |
| Connector temperature | 182 | °C | |
| Melt temperature | 179 | °C | |
| Nozzle temperature | 182 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |