| About |
|---|
| EVALENE ® LF20184 is specifically formulated for best performance in thicker films (=50 microns; =0.002″). EVALENE ® LF20184 is suitable for both the lamination and core layers in coextruded films. Films made of EVALENE ® LF20184 are notable for their toughness, flexibility and clarity – a good balance between mechanical and optical properties. The films exhibit good moisture and fair gas barrier properties, and are water resistant. FEATURES Enhanced clarity Balanced mechanical properties Meets FDA Philippines food-contact requirements Halal certified TYPICAL APPLICATIONS Flexible packaging Agricultural films Industrial liners Garment bags Trash bags Shopping bags Ice bags&& |
| Product Description | |
|---|---|
| Generic | Linear low density polyethylene |
| Material Status | Commercial: Active |
| Features | Good Clarity,High impact resistance,Smoothness,High elastic,Good tear strength,low-temperature impact resistance,Puncture Resistant,High ESCR,Low temperature heat sealing |
| Availabilitys | Asia Pacific |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.918 | g/cm³ | ASTM D1505 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 2.0 | g/10min | ASTM D1238 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| friction coefficient | ASTM D1894 | ||
| Dynamic, blow molded film | 0.090 | ASTM D1894 | |
| Static, blow molded film | 0.11 | ASTM D1894 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 25 | µm | |
| Secant modulus | ASTM D882 | ||
| 1% secant, MD: 25 µ m, blow molded film | 181 | MPa | ASTM D882 |
| 1% secant, TD: 25 µ m, blow molded film | 192 | MPa | ASTM D882 |
| tensile strength | ASTM D882 | ||
| MD, yield, 25 µ m, blow molded film | 9.00 | MPa | ASTM D882 |
| TD, yield, 25 µ m, blow molded film | 9.00 | MPa | ASTM D882 |
| MD, fracture, 25 µ m, blow molded film | 14.0 | MPa | ASTM D882 |
| TD, fracture, 25 µ m, blow molded film | 13.0 | MPa | ASTM D882 |
| Tensile strain | ASTM D882 | ||
| MD, yield, 25 µ m, blow molded film | 51 | % | ASTM D882 |
| TD, yield, 25 µ m, blow molded film | 21 | % | ASTM D882 |
| MD, fracture, 25 µ m, blow molded film | 570 | % | ASTM D882 |
| TD, fracture, 25 µ m, blow molded film | 560 | % | ASTM D882 |
| Drop hammer impact | |||
| 25 µ m, blow molded film | 61 | g | ASTM D1709 |
| Elmandorf tear strength | ASTM D1922 | ||
| MD: 25 µ m, blow molded film | 170 | g | ASTM D1922 |
| TD: 25 µ m, blow molded film | 630 | g | ASTM D1922 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 45 °, 25 µ m, blow molded film | 70 | ASTM D2457 | |
| Haze | |||
| 25 µ m, blow molded film | 16 | % | ASTM D1003 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Blow（up Ratio） | 2.00 to 4.00 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Melt temperature | 170 to 190 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 23°C |
| 3. 0.98 in/min |
| 4. 20 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |