| About |
|---|
| Exac PVDF is a Polyvinylidene Fluoride (PVDF) product. It is available in North America. Applications of Exac PVDF include engineering/industrial parts, electrical/electronic applications, aerospace, automotive and medical/healthcare. Characteristics include: Flame Rated Chemical Resistant Heat Resistant Weather Resistant&& |
| Product Description | |
|---|---|
| Supplier | Saint Gobain |
| Generic | PVDF |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Low coefficient of friction,Machinable,Self-lubricating,Solvent resistance,Heat Stabilized,V-0 |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.79 | g/cm³ | ISO 1183 |
| Water absorption rate | |||
| Saturation, 23 ℃ | 0.050 | % | |
| Equilibrium, 23 ℃, 50% RH | 0.050 | % | |
| Water absorption rate | ISO 62 | ||
| 23 ℃, 24 hours, in water | 1.0 | mg | |
| 23 ℃, 4 days, in water | 3.0 | mg | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | 10 | kJ/m² | ISO 179-1eA |
| Charpy Unnotch Impact strength | 无断裂 | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 75.0 | ℃ | ISO 75-2/A |
| Melting temperature | 175 | ℃ | |
| Linear coefficient of thermal expansion | |||
| MD | |||
| 23 to 60 ℃ | 1.3E-4 | cm/cm/℃ | |
| 23 to 100 ℃ | 1.5E-4 | cm/cm/℃ | |
| Thermal conductivity coefficient | 0.19 | W/m/K | |
| Maximum operating temperature | |||
| in air continuosly | 150 | ℃ | |
| in air for short periods | 160 | ℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+13 | ohms | IEC 60093 |
| Volume resistivity | > 1.0E+14 | ohms·cm | IEC 60093 |
| Dielectric strength | 18 | kV/mm | IEC 60243-1 |
| Relative permittivity | IEC 60250 | ||
| 100 Hz | 7.40 | ||
| 1 MHz | 6.00 | ||
| Dissipation factor | IEC 60250 | ||
| 100 Hz | 0.025 | ||
| 1 MHz | 0.17 | ||
| Compared to the leakage tracing index | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 3.00 mm | V-0 | ||
| 6.00 mm | V-0 | ||
| Extreme oxygen index | 44 | % | ISO 4589-2 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| M-level | 75 | ISO 2039-2 | |
| Ball hardness | 110 | MPa | ISO 2039-1 |
| Tensile modulus | |||
| 23℃ | 2300 | MPa | ISO 527-2 |
| tensile strength | |||
| Yield, 23 ℃ | 50.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| Fracture, 23 ℃ | > 20 | % | ISO 527-2 |
| compressive strength | ISO 604 | ||
| 2% strain | 32.0 | MPa | |
| 1% strain | 17.0 | MPa |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |