EZPrene 65A-400BSHF

About
This polyolefin based non-hygroscopic thermoplastic elastomer (TPE-V) compound is a dynamically vulcanized EPDM/PP blend with super high flow behaviour. EZPRENE® series are completely recyclable and can be processed with conventional thermoplastics machinery Additive Packages : S / Antiscratch H / Heat stabilizer Key Features : Non hygroscopic, no pre-drying Excellent ozone, UV and weathering resistance Rubberlike elasticity in a wide temperature range Super high flow for difficult injection molding applications Easy colorability with proper MB (PE, PP, etc. based) Process Method : Injection/multi injection molding Uses : Automotive: Glass encapsulation and thin-walled complex parts&&

About

This polyolefin based non-hygroscopic thermoplastic elastomer (TPE-V) compound is a dynamically vulcanized EPDM/PP blend with super high flow behaviour. EZPRENE® series are completely recyclable and can be processed with conventional thermoplastics machinery Additive Packages : S / Antiscratch H / Heat stabilizer Key Features : Non hygroscopic, no pre-drying Excellent ozone, UV and weathering resistance Rubberlike elasticity in a wide temperature range Super high flow for difficult injection molding applications Easy colorability with proper MB (PE, PP, etc. based) Process Method : Injection/multi injection molding Uses : Automotive: Glass encapsulation and thin-walled complex parts&&

Product Description
Generic	TPV
Material Status	Commercial: Active
Features	Weather resistance is good,High liquidity,High elastic,Renewable resources,Low or no water absorption,Ozone resistance,Solvent resistance,High scratch resistance,Heat Stabilized,Good coloring
Availabilitys	Europe
Process Methods	Multiple injection molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.950	g/cm³	ISO 1183/A

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shore A, 3 seconds	65		ISO 868

elastic body	Nominal value	Unit	Test method
tensile strength
fracture	5.80	MPa	ISO 37
100% strain	1.90	MPa
300% strain	2.90	MPa
Tensile strain
fracture	600	%	ISO 37
tear strength
TD	30	kN/m	ISO 34-1
Compression deformation
23℃，72 hr	27	%
70℃，22 hr	39	%
100℃，22 hr	51	%

THERMAL	Nominal value	Unit
Embrittlement temperature	-45.0	℃
Operating temperature
Dynamic	110	℃
Static	135	℃

Process Conditions
injection	Nominal value	Unit	Test method
Hopper temperature	170 to 180	°C
Barrel middle temperature	180 to 190	°C
Barrel front temperature	190 to 200	°C
Nozzle temperature	200 to 210	°C
Processing (melt) temperature	210 to 220	°C
Mold temperature	10 to 50	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.