| About |
|---|
| Fibremod GD310U is a 30% chemically coupled glass fibre reinforced polypropylene compound intended for injection moulding. This material shows excellent mechanical properties also at elevated temperatures. The product is available in standard black 8229. Applications: Fibremod GD310U has been developed especially for demanding applications in under the bonnet applications. Air Ducts Fans and shrouds Lamp housings Features: Very High Flowability&& |
| Product Description | |
|---|---|
| Supplier | Borealis AG |
| Generic | PP not specified |
| Material Status | Commercial: Active |
| Features | High liquidity,Chemical coupling |
| Availabilitys | Africa & Middle East ,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.13 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 7.0 | g/10min | ISO 1133 |
| Shrinkage rate | Internal Method | ||
| TD：2.0 mm | 0.90 | % | Internal Method |
| MD：2.0 mm | 0.20 | % | Internal Method |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -20 ℃, injection molding | 9.0 | kJ/m² | ISO 179/1eA |
| 23 ℃, injection molding | 10 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -20 ℃, injection molding | 45 | kJ/m² | ISO 179/1eU |
| 23 ℃, injection molding | 54 | kJ/m² | ISO 179/1eU |
| Impact strength of cantilever beam notch | ISO 180/1A | ||
| -20 ℃, injection molding | 9.0 | kJ/m² | ISO 180-1A |
| 23 ℃, injection molding | 10 | kJ/m² | ISO 180-1A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 145 | ℃ | ISO 75-2/A |
| Vicat Softening Temp | 133 | ℃ | ISO 306/B |
| Melt Energy | 72.8 | kJ/kg | ISO 11357 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| atomization | |||
| 16 hr，100℃ | < 2.0 | mg | DIN 75201 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| discharge | 20.0 | µgC/g | VDA 277 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| injection molding | 7200 | MPa | ISO 527-1-2 |
| tensile strength | |||
| Fracture, injection molding | 105 | MPa | ISO 527-2 |
| Tensile strain | |||
| Fracture, injection molding | 2.9 | % | ISO 527-2/50 |
| Bending modulus | |||
| injection molding | 6200 | MPa | ISO 178 |
| bending strength | |||
| injection molding | 140 | MPa | ISO 178 |
| Ball hardness | |||
| H 132/10 | 121 | MPa | ISO 2039-1 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80 | °C | |
| Drying time | 2.0 | hr | |
| Processing (melt) temperature | 230 to 280 | °C | |
| Mold temperature | 30 to 50 | °C | |
| Hold pressure | 30.0 to 60.0 | MPa | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |