| About |
|---|
| GARAFLEX G 7788-A6R IS A LEAD FREE, FLAME RETARDED, OIL RESISTANT THERMOPLASTIC ELASTOMER INTENDED FOR INSULATION AND JACKETING APPLICATIONS.&& |
| Product Description | |
|---|---|
| Generic | TPE |
| Material Status | Commercial: Active |
| Features | Flame Characteristics,Lead content is low to none,Grease resistance |
| Availabilitys | North America,Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.22 to 1.26 | g/cm³ | ASTM D792 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | 24.8 | MPa | ASTM D412 |
| Tensile strain | |||
| fracture | 500 | % | ASTM D412 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ASTM D2240 | ||
| Shaw’s A | 93 to 99 | ASTM D2240 | |
| Shore A, 15 seconds | 89 to 95 | ASTM D2240 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -60.0 | ℃ | ASTM D746 |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength in air (136 ℃, 168 hr) | 0.0 | % | UL Unspecified |
| The rate of change in ultimate elongation in air | |||
| 136℃，168 hr | -2.0 | % | UL Unspecified |
| The rate of change in tensile strength | |||
| 60℃，168 hr，in ASTM #2 Oil | -8.0 | % | UL Unspecified |
| Change in Ultimate Elongation（60℃，168 hr，in ASTM #2 Oil） | -4.0 | % | UL Unspecified |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | |||
| 23℃ | 4.0E+15 | ohms·cm | ASTM D257 |
| Dielectric constant | |||
| 23 ℃，100 MHz | 2.30 | ASTM D150 | |
| Dissipation factor | |||
| 23℃，100 MHz | 5.0E-4 | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Extreme oxygen index | |||
| 3.18 mm | 25 | % | ASTM D2863 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Barrel 1 zone temperature | 160 | °C | |
| Barrel 2 zone temperature | 177 | °C | |
| Barrel 3 zone temperature | 182 | °C | |
| Barrel 4 zone temperature | 188 | °C | |
| Barrel 5 zone temperature | 193 | °C | |
| Connector temperature | 193 | °C | |
| Melt temperature | 193 to 204 | °C | |
| Nozzle temperature | 193 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Extruded Tape |
| 3. Thickness: 30 mil |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |