| About |
|---|
| Geon™ Vinyl Rigid Molding M4300 is a Rigid Polyvinyl Chloride product. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America. Typical application: Plumbing/Piping/Potable Water. Characteristics include: Flame Rated Impact Resistant&& |
| Product Description | |
|---|---|
| Material Status | Commercial: Active |
| Features | Moderate liquidity,V-0,5VA,High impact resistance |
| Availabilitys | Latin America,Africa & Middle East ,Europe,Asia Pacific,North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.32 | g/cm³ | ASTM D792 |
| Spiral flow length | 58.4 | cm | |
| Shrinkage rate | |||
| MD | 0.20 to 0.50 | % | ASTM D955 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ASTM D256A | ||
| 0 ℃, 3.2mm, injection molding | 53 | J/m | ASTM D256-A |
| 23 ℃, 3.2mm, injection molding | 850 | J/m | ASTM D256-A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 0.45 MPa, unannealed, 6.35 mm | 70.0 | ℃ | ASTM D648 |
| 0.45 MPa, annealed, 6.35 mm | 76.1 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 6.35 mm | 67.8 | ℃ | ASTM D648 |
| 1.8 MPa, annealed, 6.35 mm | 72.8 | ℃ | ASTM D648 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 1.50 mm, all colors | V-0 | UL 94 | |
| 1.90 mm, all colors | 5VA | UL 94 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Transmittance | |||
| 3180 µm | 78.0 | % | ASTM D1003 |
| Haze | |||
| 3180 µm | 4.0 | % | ASTM D1003 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 81 | ASTM D2240 | |
| Tensile modulus | 2830 | MPa | ASTM D638 |
| tensile strength | |||
| yield | 54.5 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 30 | % | ASTM D638 |
| Bending modulus | 2760 | MPa | ASTM D790 |
| bending strength | 79.3 | MPa | ASTM D790 |
| Process Conditions | |||
|---|---|---|---|
| Injection | Nominal value | Unit | Test method |
| Processing (melt) temperature | 199 to 204 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Type I, 2.0 in/min |
| 3. CIE Illuminant C |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |