| About |
|---|
| Geon™ Vinyl Rigid Molding M5240 is a Rigid Polyvinyl Chloride product. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America. Applications of Geon™ Vinyl Rigid Molding M5240 include outdoor applications, construction applications and plumbing/piping/potable water. Characteristics include: Flame Rated Impact Resistant&& |
| Product Description | |
|---|---|
| Material Status | Commercial: Active |
| Features | Moderate liquidity,High impact resistance |
| Availabilitys | Asia Pacific,Africa & Middle East ,North America,Europe,Latin America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.41 | g/cm³ | ASTM D792 |
| Spiral flow length | 61.0 | cm | |
| Shrinkage rate | |||
| MD | 0.20 to 0.50 | % | ASTM D955 |
| Outdoor applicability | |||
| whole | f1 | UL 746C | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ASTM D256A | ||
| -18 ℃, 3.2mm, injection molding | 160 | J/m | ASTM D256-A |
| 0 ℃, 3.2mm, injection molding | 370 | J/m | ASTM D256-A |
| 23 ℃, 3.2mm, injection molding | 750 | J/m | ASTM D256-A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 0.45 MPa, unannealed, 6.35 mm | 72.8 | ℃ | ASTM D648 |
| 0.45 MPa, annealed, 6.35 mm | 77.8 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 6.35 mm | 71.1 | ℃ | ASTM D648 |
| 1.8 MPa, annealed, 6.35 mm | 76.1 | ℃ | ASTM D648 |
| Relative temperature index | 90.0 | ℃ | UL 746 |
| Electrical performance | 90.0 | ℃ | UL 746 |
| Impact mechanical performance | 85.0 | ℃ | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.50 mm, all colors | V-0 5VA | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 79 | ASTM D2240 | |
| Tensile modulus | 2340 | MPa | ASTM D638 |
| tensile strength | |||
| yield | 42.7 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 45 | % | ASTM D638 |
| Bending modulus | 2410 | MPa | ASTM D790 |
| bending strength | 71.0 | MPa | ASTM D790 |
| Process Conditions | |||
|---|---|---|---|
| Injection | Nominal value | Unit | Test method |
| Processing (melt) temperature | 199 to 210 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Type I, 2.0 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |