| About |
|---|
| GLAMIDE® T-656E is a Polyamide 66 (Nylon 66) product. It is available in North America. Characteristics include: Flame Rated Wear Resistant&& |
| Product Description | |
|---|---|
| Supplier | TOYOBO |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | Good wear resistance |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.12 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| MD：1.0 mm | 0.60-1.2 | % | ASTM D995 |
| TD：3.0 mm | 1.5-2.2 | % | ASTM D995 |
| Water absorption rate | |||
| 1.1 | % | ASTM D570 | |
| balance | 2.4 | % | ASTM D570 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 215 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 68.0 | ℃ | ASTM D648 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volumetric resistance | 1.0E+12 | Ω.cm | ASTM D257 |
| Insulation strength | |||
| 2.00mm | 21.0 | KV/mm | ASTM D149 |
| 2.00 mm, wet state | 14.0 | KV/mm | ASTM D149 |
| Dissipation factor | |||
| Arc resistance | 120 | sec | ASTM D495 |
| Volumetric resistance | 1.0E+9-1.0E+10 | Ω.cm | ASTM D257 |
| Arc resistance | 110 | sec | ASTM D495 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| – | HB | UL-94 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 145 | J/m | ASTM D256 |
| -40℃ | 100 | J/m | ASTM D256 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | 118 | R 级 | ASTM D785 |
| tensile strength | |||
| 80℃ | 30.0 | MPa | ASTM D638 |
| 23℃ | 70.0 | MPa | ASTM D638 |
| -40℃ | 95.0 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 23 ℃ | 52 | % | ASTM D638 |
| bending strength | |||
| 80℃ | 50.0 | MPa | ASTM D790 |
| 23℃ | 96.0 | MPa | ASTM D790 |
| -40℃ | 125 | MPa | ASTM D790 |
| Bending modulus | |||
| 80℃ | 800 | MPa | ASTM D790 |
| 23℃ | 2700 | MPa | ASTM D790 |
| -40℃ | 3100 | MPa | ASTM D790 |
| Taber abrasion test | <=5.0 | mg/1000 Cycles | ASTM-D1044 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Injection temperature | |||
| Mold temperature | 40.0-80.0 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |