| About |
|---|
| Grivory® GV-6 FWA black 9225 is a Polyamide 66 + PA 6I/X (Nylon 66+Nylon 6I/X) material filled with 60% glass fiber. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America for extrusion or injection molding. Important attributes of Grivory® GV-6 FWA black 9225 are: Flame Rated RoHS Compliant Food Contact Acceptable Typical applications include: Plumbing/Piping/Potable Water Food Contact Applications Consumer Goods Engineering/Industrial Parts Household Applications&& |
| Product Description | |
|---|---|
| Supplier | EMS-GRIVORY |
| Generic | PA 66+PA 6I/X |
| Material Status | Commercial: Active |
| Features | Low warping,Good Dimensional Stability,Solvent resistance,Aromatic,Good surface appearance,high-rigidity |
| Availabilitys | Africa & Middle East ,Asia Pacific,Europe,North America,Latin America |
| Process Methods | Injection Molding,Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.69 | g/cm³ | ISO 1183 |
| Linear mold shrinkage | ISO 294-4 | ||
| long. | 0.05 | % | ISO 294-4 |
| trans. | 0.30 | % | ISO 294-4 |
| ISO 62 | |||
| Saturation, 23 ℃ | 3.5 | % | ISO 62 |
| Balanced Equilibrium, 23 ℃, 50% RH | 1.2 | % | ISO 62 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy notch Impact strength | ISO 179/1eA | ||
| -30℃ | 13 | kJ/m² | ISO 179/1eA |
| 23℃ | 14 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -30℃ | 80 | kJ/m² | ISO 179/1eU |
| 23℃ | 80 | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature HDT | |||
| 1.8 MPa, unannealed | 235 | ℃ | ISO 75-2/A |
| 8.0 MPa, unannealed | 175 | ℃ | ISO 75-2/C |
| — | 100 to 120 | ℃ | ISO 2578 |
| — | 220 | ℃ | Internal Method |
| 260 | ℃ | ISO 11357-3 | |
| Linear thermal expansion coefficient | ISO 11359-2 | ||
| MD | 1.5E-5 | 1/℃ | ISO 11359-2 |
| TD | 9.0E-5 | 1/℃ | ISO 11359-2 |
| ELECTRICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1E13 | ohms | IEC 60093 |
| Volume resistivity | 1E12 | ohms·cm | IEC 60093 |
| Dielectric strength | 33 | kV/mm | IEC 60243-1 |
| Compared to the leakage tracing index | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flammability level | |||
| 0.8 mm | HB | ISO 1210 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Ball indentation hardness | 315 | MPa | ISO 2039-1 |
| 22000 | MPa | ISO 527-2 | |
| Tensile strength | |||
| Break | 260 | MPa | ISO 527-2 |
| 2 | % | ISO 527-2 |
| Process Conditions | |||
|---|---|---|---|
| Injection molding | Nominal value | Unit | Test method |
| Drying temperature | max 80 | ℃ | |
| Drying time | 4-12 | h | |
| Dew point of the dryer | -25 | ℃ | |
| Vacuum oven temperature | max 100 | ℃ | |
| Flange temperature | 80 | ℃ | |
| Barrel 1 temperature zone 1 temperature | 260 | ℃ | |
| Barrel 2 temperature zone 2 temperature | 270 | ℃ | |
| Barrel 3 temperature zone 3 temperature | 275 | ℃ | |
| Nozzle temperature | 270 | ℃ | |
| Tool temperature | 80-120 | ℃ | |
| Melt temperature | 270-300 | ℃ | |
| Injection speed | 中速to高速 | ||
| Hold on pressure | 300-800 | bar | |
| Dynamic pressure | 50-100 | bar | |
| Screw speed | 0.1-0.3 | m/s | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Long Term |
| 3. Short Term |
| 4. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |