| About |
|---|
| Halar® 500LC is an Ethylene Chlorotrifluoroethylene Copolymer (ECTFE) material. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America for extrusion or injection molding. Important attributes of Halar® 500LC are: Flame Rated Low Viscosity Typical application of Halar® 500LC: Wire & Cable&& |
| Product Description | |
|---|---|
| Supplier | Solvay |
| Generic | ECTFE |
| Material Status | Commercial: Active |
| Features | Low Viscosity |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.68 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| MD | 2.5 | % | ASTM D995 |
| Melt Flow Rate | |||
| 275℃，2.16kg | 18 | g/10min | ASTM D1238 |
| Saturated water absorption | <=0.10 | % | ASTM D570 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 90.0 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 65.0 | ℃ | ASTM D648 |
| Melting temperature | 242 | ℃ | |
| Glass transition temperature | 85.0 | ℃ | ASTM D648 |
| Vicat Softening Temp | |||
| Linear coefficient of thermal expansion | |||
| MD | 10E-3 | 1/℃ | ASTM D696 |
| Embrittlement temperature | <=-76.0 | ℃ | ASTM D746 |
| Thermal conductivity coefficient | 0.150 | W/m/K | JIS R2618 |
| Crystallization temperature | 222 | ℃ | ASTM D3418 |
| Specific heat capacity | 962 | J/Kg/℃ | ASTM C351 |
| Fusion heat | 42.0 | J/g | ASTM D3418 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volumetric resistance | 1.0E+16 | Ω.cm | ASTM D257 |
| Insulation strength | |||
| 3.18 mm | 22 | KV/mm | ASTM D149 |
| Dielectric constant | |||
| 2.57 | 1 MHz | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 0.18mm | V-0 | UL 94 | |
| 1.50mm | V-0 | UL 94 | |
| 3.00mm | V-0 | UL 94 | |
| Extreme oxygen index | 52 | % | ASTM D2863 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | NB | J/m | ASTM D256 |
| -40℃ | 2.10 | J/m | ASTM D256 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| yield | 5.0 | % | ASTM D638 |
| Shore hardness | |||
| Shaw’s A | 75 | ASTM D2240 | |
| Rockwell hardness | 90 | R 级 | ASTM D785 |
| tensile strength | |||
| 断裂，50mm/min，23°C | 47.0 | MPa | ASTM D638 |
| 屈服，50mm/min，23°C | 30.0 | MPa | ASTM D638 |
| Tensile modulus | |||
| 23℃，50 mm/min | 1660 | MPa | ASTM D638 |
| bending strength | |||
| 2.50 mm/min，23℃ | 47.0 | MPa | ASTM D790 |
| Bending modulus | |||
| 2.50 mm/min，23℃ | 1690 | MPa | ASTM D790 |
| Friction coefficient | |||
| dynamic | 0.20 | ASTM D3702 | |
| static state | 0.30 | ASTM D3702 | |
| Taber wear and tear | 5.0 | mg/1000cy | ASTM D1044 |
| Tensile strain |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 2.0 in/min |
| 3. 0.098 in/min |
| 4. 50% RH |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |