| About |
|---|
| Description Non-flammable PP FB51 and FB51R, which are designed with base resin that has excellent shock resistance, exhibit high shock resistance. In particular, its excellent fluidity allows good formability and nice exterior with high non-flammability so to be Widely used for exterior of electric/electronic parts. Characteristics FB51: As non-flammability grade of UL94 V-2, it provides fluidity and shock resistance, nice exterior, in particular, long-term thermal stability). Thus, it belongs to UL746B RTI 130 QC Class, the World top standard, as PP material. It is Widely used for exterior of heat transmission/electric/electronic products like a fan heater. Applications Fan heater exterior (FB51, FB51R) Other electric/electronic parts needing shock resistance and non-flammability (FB51, FB51R)&& |
| Product Description | |
|---|---|
| Supplier | HANWHA |
| Generic | PP not specified |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Excellent Processability,High impact resistance,Good Dimensional Stability,High liquidity,Flame Characteristics,Heat Stabilized,V-2 |
| Availabilitys | North America,Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.930 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 8.0 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD：2.0 mm | 1.5 to 1.9 | % | ASTM D955 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 69 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 120 | ℃ | ASTM D648 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 0.80 mm | V-2 | UL 94 | |
| Flammability | |||
| 1.59 mm | 130 | ℃ | UL 746B |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 90 | ASTM D785 | |
| tensile strength | |||
| yield | 29.4 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 200 | % | ASTM D638 |
| Bending modulus | 1470 | MPa | ASTM D790 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 90 to 100 | °C | |
| Drying time | 2.0 | hr | |
| Barrel rear temperature | 170 to 180 | °C | |
| Barrel middle temperature | 180 to 200 | °C | |
| Barrel front temperature | 180 to 200 | °C | |
| Nozzle temperature | 190 to 210 | °C | |
| Mold temperature | 40 to 70 | °C | |
| Injection pressure | 39.2 to 78.5 | MPa | |
| Back pressure | 0.490 to 1.96 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 2.0 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |