Hepla® H2000 CM

About
Hepla® H2000 CM Resin is a blend of Polyphenylene Ether(PPE) + Polyamide(PA) resin that is mineral filled, and suitable for injection molding. The conductivity level is optimized to allow for primer-less electrostatic painting. Hepla® H2000 CM has improved impact/elongation and the mineral content enables the material to be used in structural applications replacing metal or thermoset resins. The material is only available in black.

About

Hepla® H2000 CM Resin is a blend of Polyphenylene Ether(PPE) + Polyamide(PA) resin that is mineral filled, and suitable for injection molding. The conductivity level is optimized to allow for primer-less electrostatic painting. Hepla® H2000 CM has improved impact/elongation and the mineral content enables the material to be used in structural applications replacing metal or thermoset resins. The material is only available in black.

Product Description
Supplier	NFD
Generic	PPO(PPE)
Material Status	Commercial: Active
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.24	g/cm³	ASTM D792
Density	1.24	g/cm³	ISO 1183
Moisture Absorption
Equilibrium, 23 ℃, 50% RH	0.7	%	ISO 62
Saturation, 23℃	3.6	%	ISO 62
Shrinkage rate
MD：3.20 mm	0.7 to 0.9	%	NFD Method
Melt Flow Rate
280℃，5.0 kg	16	g/10 min	ASTM D1238
Melt Volume Rate
220℃，5.0 kg	14	cm3/10min	ISO 1133

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus	4921	MPa	ISO 527-2/1
Tensile Modulus, 5.0 mm/min	4673	MPa	ASTM D638
Tensile Stress, yield, Type I
5.0 mm/min	65.6	MPa	ASTM D638
Tensile Stress, break, Type I
5.0 mm/min	63.4	MPa	ASTM D638
Tensile Strain, yield, Type I
5.0 mm/min	2.9	%	ASTM D638
Tensile Strain, break, Type I
5.0 mm/min	3.8	%	ASTM D638
tensile strength
yield	62.3	MPa	ISO 527-2/5
tensile strength
fracture	62.3	MPa	ISO 527-2/5
Tensile strain
yield	2	%	ISO 527-2/5
Tensile strain
fracture	4.8	%	ISO 527-2/5
Flexural Modulus, 2.0 mm/min	4627	MPa	ISO 178
Flexural Modulus, 50.0 mm Span
1.3 mm/min	4199	MPa	ASTM D790
Flexural Stress, yield
2.0 mm/min	111.3	MPa	ASTM D790
Flexural Stress, break
50.0 mm Span, 1.3 mm/min	110.5	MPa	ASTM D790

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch, 23 ℃	39.7	J/m	ASTM D256
Unnotched Izod Impact, -30℃	31.5	J/m	ASTM D4812
Impact strength of cantilever beam notch
80104 , 23℃	4.3	kJ/m2	ISO 180/1A
Notched impact strength of cantilever beam
80104 ,-30℃	3.5	kJ/m2	ISO 180/1A
Charpy Notched Impact Strength
80104, 23℃	3.8	kJ/m2	ISO 179/1eA
Dart impact strength
23℃, Total Energy	7	J	ASTM D3763

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
Bf,0.45 MPa Flatw 80104 sp=64mm	184	℃	ISO 75/Bf
0.45MPa, unannealed, 3.2mm	185	℃
Vicat Softening Temp
B50	185	℃	ASTM D1525, ISO 306
B120	188	℃	ISO 306
Linear coefficient of thermal expansion
Flow : -40 to 40℃	6.00E-05	1/℃	ASTM E831, ISO 11359-2
Transverse : -40 to 40℃	6.50E-05	1/℃	ASTM E831, ISO 11359-2

Process Conditions
Processing technology	Nominal value	Unit	Test method
Maximum Moisture Content	0.07	%
Suggested Shot Size	30 to 50	%
Melt Temperature	277 to 300	℃
Nozzle Temperature	277 to 300	℃
Mold temperature	66 to 94	℃
drying temperature	93 to 107	℃
Drying time	3 to 4	hr
Drying Time, Maximum	8	hr
Front temperature of material barrel	270 to 300	℃
Temperature in the middle of the barrel	266 to 300	℃
Temperature at the rear of the barrel	260 to 300	℃
Back pressure	0.345 to 1.38	MPa
Screw Speed	20 to 100	rpm
Vent Depth	0.013 to 0.038	mm

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.