HI-ZEX MILLION™ 630M

About
HI-ZEX MILLION™ 630M is a High Molecular Weight Polyethylene material. It is available in Asia Pacific for extrusion, press molding, or ram extrusion. Important attributes of HI-ZEX MILLION™ 630M are: Impact Resistant Chemical Resistant Food Contact Acceptable Moisture Resistant Wear Resistant Typical applications include: Engineering/Industrial Parts Food Contact Applications Medical/Healthcare Agricultural Bags/Liners&&

About

HI-ZEX MILLION™ 630M is a High Molecular Weight Polyethylene material. It is available in Asia Pacific for extrusion, press molding, or ram extrusion. Important attributes of HI-ZEX MILLION™ 630M are: Impact Resistant Chemical Resistant Food Contact Acceptable Moisture Resistant Wear Resistant Typical applications include: Engineering/Industrial Parts Food Contact Applications Medical/Healthcare Agricultural Bags/Liners&&

Product Description
Supplier	Mitsui
Generic	HMW-HDPE
Material Status	Commercial: Active
Features	High impact resistance,Low or no water absorption,Food contact compliance,Self-lubricating,Good wear resistance,Solvent resistance,low-temperature impact resistance
Availabilitys	Asia Pacific
Process Methods	Extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.930	g/cm³	ASTM D1505
Apparent density	0.43	g/cm³	ASTM D1895
Water absorption rate
23℃，24hr	< 0.010	%	ASTM D570
Average molecular weight	5.90E+6		Internal Method
Average particle size	160	µm	Internal Method

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch	55.0	kJ/m²	ASTM D256

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	75.0	℃	ASTM D648
Melting peak temperature	136	℃	ASTM D3418
Linear coefficient of thermal expansion
MD	1.5E-6	1/℃	ASTM D696
Thermal conductivity coefficient	0.40	W/m/K	ASTM C177

Electrical performance	Nominal value	Unit	Test method
Volume resistivity	1.0E+17 to 1.0E+18	ohms·cm	ASTM D257
Dielectric strength	50	kV/mm	ASTM D149
Dielectric constant	2.30		ASTM D150
Dissipation factor	2.0E-4 to 3.0E-4		ASTM D150

Supplementary information	Nominal value	Unit	Test method
Dynstat Impact	62.0	kJ/m²	Internal Method
Sand Abrasion Wear（1600rpm，3h）	3.0	mg	Internal Method

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness
R-level	40		ASTM D785
tensile strength
fracture	39.0	MPa	ASTM D638
Tensile strain
fracture	260	%	ASTM D638
Bending modulus	390	MPa	ASTM D790
friction coefficient	0.20		ASTM D1894
Wear resistance	< 10	mm³	ASTM D1044

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.