| About |
|---|
| 47 Shore D Standard Performance Polyester Elastomer with Heat Ageing Protection&& |
| Product Description | |
|---|---|
| Supplier | DuPont |
| Generic | TPC-ET |
| Material Status | Commercial: Active |
| Features | Good heat aging resistance,Heat Stabilized,HB |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Shore hardness | ISO 868 | ||
| Shaw’s D | 48 | ISO 868 | |
| Shore D, 15 seconds | 43 | ISO 868 | |
| Tensile modulus | 110 | MPa | ISO 527-2 |
| tensile strength | ISO 527-2 | ||
| fracture | 17.0 | MPa | ISO 527-2 |
| 10% strain | 7.00 | MPa | ISO 527-2 |
| 50% strain | 12.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 200 | % | ISO 527-2 |
| Nominal tensile fracture strain | 400 | % | ISO 527-2 |
| Bending modulus | 111 | MPa | ISO 178 |
| shear modulus | 39.0 | MPa | ISO 6721 |
| Poisson’s ratio | 0.40 | ISO 527 | |
| abrasion resistance | 33.0 | mm³ | ISO 4649 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tear strength | ISO 34-1 | ||
| TD | 90 | kN/m | ISO 34-1 |
| MD | 100 | kN/m | ISO 34-1 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -40 ℃, localized fracture | 120 | kJ/m² | ISO 179/1eA |
| -30℃ | No Break | ISO 179/1eA | |
| 23℃ | No Break | ISO 179/1eA | |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -30℃ | No Break | ISO 179/1eU | |
| 23℃ | No Break | ISO 179/1eU | |
| Impact strength of cantilever beam notch | ISO 180/1A | ||
| -40℃ | No Break | ISO 180/1A | |
| 23℃ | No Break | ISO 180/1A | |
| Tensile impact strength | |||
| 23℃ | 260 | kJ/m² | ISO 8256/1 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -66.0 | ℃ | ISO 974 |
| Glass transition temperature | -45.0 | ℃ | ISO 11357-2 |
| Melting temperature | 208 | ℃ | ISO 11357-3 |
| Linear coefficient of thermal expansion | |||
| TD | 1.9E-4 | 1/℃ | ISO 11359-2 |
| MD | 2.2E-4 | 1/℃ | ISO 11359-2 |
| Effective Thermal Diffusivity | 5.44E-8 | m²/s |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+14 | ohms·cm | IEC 60093 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Burning rate | |||
| 1 mm | 33 | mm/min | ISO 3795 |
| Flame retardant level | UL 94 | ||
| 1.50 mm | HB | UL 94 | |
| 3.00 mm | HB | UL 94 | |
| Flammability level | IEC 60695-11-10, -20 | ||
| 1.5 mm | HB | IEC 60695-11-10, -20 | |
| 3.0 mm | HB | IEC 60695-11-10, -20 | |
| FMVSS flame retardant rating | B | FMVSS 302 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Emissions of organic compounds | 18.0 | µgC/g | VDA 277 |
| Odor | 5.00 | VDA 270 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.19 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 11 | g/10min | ISO 1133 |
| Melt Volume Rate | |||
| 230℃，2.16 kg | 11.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | ISO 294-4 | ||
| TD | 1.2 | % | ISO 294-4 |
| MD | 1.5 | % | ISO 294-4 |
| Water absorption rate | |||
| 23℃，24hr | 2.5 | % | ISO 62 |
| Melt density | 1.01 | g/cm³ | |
| Specific Heat Capacity of Melt | 2100 | J/kg/℃ | |
| Thermal Conductivity of Melt | 0.16 | W/m/K |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 100 | °C | |
| Drying time – hot air dryer | 2.0 to 3.0 | hr | |
| Recommended maximum moisture content | 0.080 | % | |
| Processing (melt) temperature | 235 to 260 | °C | |
| Melt Temperature, Optimum | 240 | °C | |
| Mold temperature | 45 to 55 | °C | |
| Mold Temperature, Optimum | 45 | °C | |
| Drying Recommended | yes | ||
| Recommended maximum moisture content | 0.060 | % | |
| Extrusion Melt Temperature, Optimum | 230 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 10°C/min |
| 3. FMVSS 302 |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |