| About |
|---|
| Ingeo 3260HP is a low viscosity product from NatureWorks, designed for high flow injection molding applications. It is designed to crystallize during processing, leading to higher heat deflection temperatures in opaque applications. The variety of products made with 3260HP is widely varied and growing. Applications include disposables such as cutlery, cups, plates, cosmetic packaging, and durables such as electronics housings.&& |
| Product Description | |
|---|---|
| Generic | PLA |
| Material Status | Commercial: Negative |
| Features | Renewable resources,Low Viscosity,Crystal,Food contact compliance,Compostable |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.24 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 210℃，2.16kg | 65 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD | 0.20 to 0.40 | % | |
| MD | 1.7 to 1.8 | % | |
| Relative viscosity | |||
| 30℃ | 2.50 | ASTM D5225 | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| yield | 63.4 | MPa | ASTM D638 |
| Tensile strain | ASTM D638 | ||
| fracture | 3.0 | % | ASTM D638 |
| fracture | 1.3 | % | ASTM D638 |
| Bending modulus | ASTM D790 | ||
| — | 3590 | MPa | ASTM D790 |
| — | 4300 | MPa | ASTM D790 |
| bending strength | 108 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 16 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM E2092 | ||
| 0.45 MPa, unannealed | 56.0 | ℃ | ASTM E2092 |
| 0.45 MPa, unannealed | 151 | ℃ | ASTM E2092 |
| Crystallization peak temperature | |||
| DSC | 165 to 180 | ℃ | ASTM D3418 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Recommended maximum moisture content | 0.025 | % | |
| Barrel rear temperature | 175 | °C | |
| Barrel middle temperature | 185 | °C | |
| Barrel front temperature | 190 | °C | |
| Nozzle temperature | 190 | °C | |
| Processing (melt) temperature | 199 | °C | |
| Mold temperature | 120 | °C | |
| Back pressure | 1.72 | MPa | |
| Screw speed | 200 | rpm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Crystalline, 120°C Mold Temperature |
| 3. Amorphous, 26°C Mold Temperature |
| 4. 1.0 g/dL in chloroform |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |