| About |
|---|
| Ingeo biopolymer 6100D, a NatureWorks product, is a thermoplastic fiber-grade resin derived primarily from annually renewable resources. Available in pellet form, 6100D is designed for extrusion into mechanically drawn staple fibers or continuous filament, using conventional fiber spinning and drawing equipment. 6100D is typically well suited for fiber processes where lower fiber shrinkage and higher dimensional stability is required. Ingeo biopolymer 6100D can be converted into a broad range of fiber products. Potential applications for Ingeo biopolymer 6100D include: Staple fiber Nonwovens Agricultural woven and nonwoven fabrics Articles for household disposal Textiles Continuous filament – Textured and flat yarns Spunbond fabrics&& |
| Product Description | |
|---|---|
| Generic | PLA |
| Material Status | Commercial: Active |
| Features | Good Dimensional Stability,Renewable resources,Food contact compliance |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Modulus of Elasticity | 55.0 to 65.0 | g/denier | ASTM D2256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Glass transition temperature | 55.0 to 60.0 | ℃ | ASTM D3417 |
| Crystallization peak temperature | |||
| DSC | 165 to 180 | ℃ | ASTM D3418 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Denier（per filament） | > 0.500 | ||
| Elongation of Fibers | 10 to 70 | % | ASTM D2256 |
| Tenacity of Fibers | 3.00 to 6.00 | g/denier | ASTM D2256 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.24 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 210℃，2.16kg | 24 | g/10min | ASTM D1238 |
| Relative viscosity | 3.1 | ASTM D5225 | |
| Shrinkage rate | ASTM D2102 | ||
| boiled water | 3.0-10 | % | ASTM D2102 |
| Hot air: 130 ℃, 10 minutes | 3.0-10 | % | ASTM D2102 |
| Melt density | |||
| 230℃ | 1.08 | g/cm³ |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 80 | °C | |
| Drying time | 4.0 to 6.0 | hr | |
| Recommended maximum moisture content | < 5.0E-3 | % | |
| Melt temperature | 220 to 240 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Measured at 1.0 g/dL in chloroform at 30°C |
| 3. 10 min |
| 4. g/9000m |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |