| About |
|---|
| RTVS 61M is a low viscosity, self-extinguishing transparent RTVS Silicone. RTVS 61M is used in situations where component identification and protection against shock and vibration is needed. Heat can be used to accelerate the cure.&& |
| Product Description | |
|---|---|
| Generic | 硅橡胶,RTV-2 |
| Material Status | Commercial: Active |
| Features | Low Viscosity,Self-extinguishing |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Shore hardness | |||
| Shaw’s A | 35 | ASTM D2240 | |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | 2.76 | MPa | ASTM D412 |
| Tensile strain | |||
| fracture | 150 | % | ASTM D412 |
| tear strength | 4.38 | kN/m | ASTM D624 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+15 | ohms·cm | ASTM D257 |
| Dielectric strength | 20 | kV/mm | ASTM D149 |
| Dielectric constant | |||
| 1 kHz | 2.70 | ASTM D150 | |
| Dissipation factor | |||
| 1 kHz | 1.0E-3 | ASTM D150 |
| Uncured Properties | Nominal value | Unit | Test method |
|---|---|---|---|
| colour | |||
| — | Clear/Transparent | ||
| Density | |||
| — | 0.998 | g/cm³ | |
| — | 1.02 | g/cm³ | |
| viscosity | ASTM D2393 | ||
| — | 4.0 | Pa·s | ASTM D2393 |
| — | 4.5 | Pa·s | ASTM D2393 |
| — | 5.0 | Pa·s | ASTM D2393 |
| Curing time | |||
| 95℃ | 1.0 | hr | |
| 50℃ | 2.0 | hr | |
| 25℃ | 24 | hr | |
| storage stability | |||
| 25 ℃ | 120 | min |
| Cured Properties | Nominal value | Unit | Test method |
|---|---|---|---|
| Linear Shrinkage | 0.20 | % |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Linear coefficient of thermal expansion | |||
| MD | 2.7E-4 | 1/℃ | |
| Thermal conductivity coefficient | 0.19 | W/m/K | |
| Operating temperature | -55 to 204 | ℃ | |
| Thermosetting components | |||
| Component A | 按重量计算的混合比: 10 | ||
| Component B | 按重量计算的混合比: 1.0 | ||
| Storage period | |||
| 25℃ | 26 | wk |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die B |
| 3. Part B |
| 4. Part A |
| 5. Mixed |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |