| About |
|---|
| Isothane 1065AU-F1 resin is a polyester based thermoplastic polyurethane having high elasticity and recovery. It has excellent mechanical properties and good damping characteristics. Isothane 1065AU-F1 can be processed by extrusion and injection molding.&& |
| Product Description | |
|---|---|
| Supplier | Great Eastern |
| Generic | TPU-酯 |
| Material Status | Commercial: Active |
| Features | High elastic |
| Availabilitys | North America,Asia Pacific,Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.18 | g/cm³ | ASTM D792 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| 100% strain | 2.00 | MPa | |
| 300% strain | 6.00 | MPa | |
| tensile strength | 28.0 | MPa | ASTM D412 |
| Tensile strain | |||
| fracture | 720 | % | ASTM D412 |
| tear strength | 70.0 | kN/m | ASTM D624 |
| Compression deformation | |||
| 23℃，22 hr | 40 | % | ASTM D395 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s A | 62 to 68 | ASTM D2240 | |
| abrasion resistance | 102.0 | mg | DIN 53516 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature – hot air dryer | 80 | °C | |
| Drying time – hot air dryer | 3.0 to 5.0 | hr | |
| Dew Point – Hot Air Dryer | -40 to -30 | °C | |
| Recommended maximum moisture content | 0.020 | % | |
| Proposed maximum recycled material ratio | 20 | % | |
| Barrel rear temperature | 165 to 170 | °C | |
| Barrel middle temperature | 175 to 180 | °C | |
| Barrel front temperature | 175 to 180 | °C | |
| Nozzle temperature | 170 to 175 | °C | |
| Injection pressure | 41.4 to 103 | MPa | |
| Injection speed | 慢to中等 | ||
| Screw compression ratio | 2.0 : 1.0 to 3.0 : 1.0 | ||
| Drying temperature | 80 | °C | |
| Drying time | 3.0 to 5.0 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Proposed maximum recycled material ratio | 20 | % | |
| Barrel 1 zone temperature | 160 to 165 | °C | |
| Barrel 3 zone temperature | 170 to 175 | °C | |
| Barrel 5 zone temperature | 170 to 175 | °C | |
| Nozzle temperature | 165 to 170 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |