| About |
|---|
| Kalix® 9850 is a 50% glass-fiber reinforced high-performance polyamide. It is hot-water moldable and intended for use in components requiring superior mechanical properties and excellent surface quality. Kalix® 9850 is characterized by high stiffness and strength, very good impact properties, good dimensional stability, and excellent surface finish. Kalix® 9850 exhibits an excellent combination of high flow, low flash tendency and fast cycle time which makes it a cost-competitive option for thin-walled parts produced in large quantities, such as structural parts in mobile electronic devices. Black: Kalix® 9850 BK 000&& |
| Product Description | |
|---|---|
| Supplier | Solvay |
| Generic | HPPA |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good surface appearance,High impact resistance,Good Dimensional Stability,High liquidity,Sprayable,Quick molding cycle,Electroplating |
| Availabilitys | North America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.60 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| TD | 0.60 | % | |
| MD | 0.15 | % | |
| Water absorption rate | |||
| 23℃，24hr | 0.39 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 20000 | MPa | ISO 527-2 |
| tensile strength | |||
| yield | 290 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 2.7 | % | ISO 527-2 |
| Bending modulus | 19000 | MPa | ISO 178 |
| bending strength | |||
| 3.50% strain | 425 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 18 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | 95 | kJ/m² | ISO 180 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 248 | ℃ | ISO 75-2/A |
| Melting peak temperature | 260 | ℃ | ASTM D3418 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric constant | |||
| 2.40 GHz | 3.86 | ASTM D2520 | |
| Dissipation factor | |||
| 2.4 GHz | 0.011 | ASTM D2520 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80 | °C | |
| Drying time | 4.0 to 12 | hr | |
| Recommended maximum moisture content | 0.090 | % | |
| Barrel rear temperature | 250 | °C | |
| Barrel front temperature | 280 | °C | |
| Processing (melt) temperature | 285 to 305 | °C | |
| Mold temperature | 80 to 120 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Solvay Test Method. Shrink rates can vary with part design and processing conditions. Please consult a Solvay Technical Representative for more information. |
| 3. Method B |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |